Pengaruh Variasi Tebal Orifice dan Bilangan Reynolds (Re) terhadap Penurunan Tekanan (Pressure Drop) pada Entrance Region
DOI:
https://doi.org/10.18196/jqt.v4i2.16154Keywords:
Orifice, Reynolds Number, Pressure Drop, Coefficient of DischargeAbstract
Orifice is a device that is placed in a pipe flow to inhibit the flow of fluid and cause a pressure drop. The measurement of the flow rate (flow rate) is obtained from the difference in pressure due to the pressure drop. In this study, it analyzed the influence of differences in plate orifice thickness variations used ranging from 2 mm to 4 mm thick with variations in increments every 0.5 mm with an orifice center hole diameter of 1.5 cm. Orifice placement is placed in an area whose speed profile is still changing or called the entrance region with a pipe diameter used 2.54 cm (1 Inch) diameter in the pipe. Then along the entrance area are paired 12 piezometer points along 75 cm with a position of laying 6 piezometer points before the orifice valve and 6 piezometer points after the orifice valve and in this experiment set the Re value to 3 Variations of Re, namely Re 1: 9784.5; Re2: 14647.5; Re 3: 19510.45 and this experiment was carried out at a temperature of 27 °C. In this study, the results were obtained for the highest irrecoverable pressure drop value located in the flow discharge with Re 19510.45 and at the thickness of the plate orifice 4 mm with an irrecoverable pressure drop value of 3033.01 Pa and while for the lowest irrecoverable pressure drop value, it was located in the flow discharge with a value of Re 9784.5 at an orifice plate thickness of 2 mm with an irrecoverable pressure drop value of 548.26 Pa. The highest discharge of coefficient (Cd) value lies in the flow discharge with a value of Re 14647.5 at the plate orifice thickness of 3.5 with a Cd value of 0.718 and while for the lowest discharge of coefficient (Cd) value lies in the flow discharge with Re 14647.5 with an orifice plate thickness of 2 mm with a Cd value of 0.609.
References
Abd, H. M., Alomar, O. R., & Mohamed, I. A. (2019). Effects of varying orifice diameter and Reynolds number on discharge coefficient and wall pressure. Flow Measurement and Instrumentation, 65, 219-226.
Gerhart, P. M., Gerhart, A. L., & Hochstein, J. I. (2016). Munson, Young and Okiishi's Fundamentals of Fluid Mechanics. John Wiley & Sons.
Ghurri, A., & Septiadi, I. W. N. (2006). Studi Eksperimen Orifice Flow Meter dengan Variasi Posisi Pengukuran Beda-Tekanan Aliran melintasi Orifice Plate.
Ghurri, A., Tisna, S. G., & Syamsudin, S. (2016). Pengujian Orifice Flow Meter dengan Kapasitas Aliran Rendah. Mechanical, 7(2)
Gomez-Perez, Y. A., Carrillo-Garcia, M., Jimenez-Hernandez, E., Valle-Guadarrama, S., & Vazquez-Peña, M. A. (2015). Design, Construction and Operation of Modest Orifice Plate Flow-Meter for Irrigation Wells. In 2015 ASABE Annual International Meeting (p. 1). American Society of Agricultural and Biological Engineers.
Tardi, G., Massaroni, C., Saccomandi, P., & Schena, E. (2015). Experimental assessment of a variable orifice flowmeter for respiratory monitoring. Journal of Sensors, 2015.
LaNasa, P. J., & Upp, E. L. (2014). Fluid flow measurement: A practical guide to accurate flow measurement. Butterworth-Heinemann.
Reader-Harris, M. (2015). Orifice plates and venturi tubes (pp. 13-14). Basel, Switzerland: Springer International Publishing.
Septiadi, W. N. (2008). Studi eksperimental orifice flow meter dengan variasi tebal dan posisi pengukuran beda tekanan aliran melintasi orifice plate. Jurnal Ilmiah Teknik Mesin CAKRAM Vol, 2(1), 61-68.
Spitzer, D. W. (1991). Flow Measurement: Partical Guides for Measureent and Control. North California: Instrument Society of America.
Vemulapalli, S., & Venkata, S. K. (2022). Parametric analysis of orifice plates on measurement of flow: A review. Ain Shams Engineering Journal, 13(3), 101639.
Downloads
Published
How to Cite
Issue
Section
License
Copyright
The Authors submitting a manuscript do so on the understanding that if accepted for publication, the copyright of the article shall be assigned to Quantum Teknika : Jurnal Teknik Mesin Terapan as the publisher of the journal. Copyright encompasses rights to reproduce and deliver the article in all forms and media, including reprints, photographs, microfilms, and any other similar reproductions, as well as translations.
Authors should sign Copyright Transfer Agreement when they have approved the final proofs sent by Quantum Teknika : Jurnal Teknik Mesin Terapan prior to the publication. Quantum Teknika : Jurnal Teknik Mesin Terapan strive to ensure that no errors occur in the articles that have been published, both data errors and statements in the article.
Quantum Teknika : Jurnal Teknik Mesin Terapan keep the rights to articles that have been published. Authors are permitted to disseminate published articles by sharing the link to Quantum Teknika : Jurnal Teknik Mesin Terapan website. Authors are allowed to use their works for any purposes deemed necessary without written permission from Quantum Teknika : Jurnal Teknik Mesin Terapan with an acknowledgment of initial publication in this journal.
License
All articles published in Quantum Teknika : Jurnal Teknik Mesin Terapan are licensed under a Creative Commons Attribution-NonCommercial 4.0 International License (CC-BY-NC). You are free to :
1. Share – copy and redistribute the material in any medium or format.
2. Adapt – remix, transform, and build upon the material.
The licensor cannot revoke these freedoms as long as you follow the license terms, which include the following:
1. Attribution - you must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
2. NonCommercial - You may not use the material for commercial purposes.
3. No additional restrictions - You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
