Gabungan Quenching-Variasi Tekanan Shot peening Terhadap Kekerasan Permukaan dan Struktur Mikro Permukaan Baja S45C

Bambang Hari Priyambodo, Margono Margono, Rizqi Ilmal Yaqin

Abstract


The combination of Quenching and Shot peening (SP) heat treatment is rarely carried out, especially the use of this treatment can improve the mechanical properties of medium carbon steel (S45C). This study aims to analyze the microstructure and hardness of S45C steel with the combined effect of Quenching heat treatment with shot peening with variations in compressor air pressure. Commercial S45C steel is quenched with a heating temperature of 910oC and held for 15 minutes. In comparison, the SP process is carried out after the quenching process with variations in air pressure, namely 4, 5, 6, and 7 bar. Analysis of the combined results of Quenching and SP processes using hardness and microstructure. The investigation analysis results obtained specimens with the highest surface hardness in the quenching and SP treatment of 899.44 HV. The impact of SP on the surface up to a distance of 120 m from the surface. The highest hardness was in the Quenching and SP treatment with a pressure of 7 bar. The results of this study are used as parameter contributions in the area of surface treatment and heat treatment of carbon steel to be developed in the automotive industry.

Keywords


Quenching; Microstructure; S45C; Surface Hardness.

Full Text:

PDF

References


Adeleke, A. A., Ikubanni, P. P., Orhadahwe, T. A., Aweda, J. O., Odusote, J. K., & Agboola, O. O. 2019. Microstructural assessment of AISI 1021 steel under rapid cyclic heat treatment process. Results in Engineering, 4, 1–4. https://doi.org/10.1016/j.rineng.2019.100044

Agboola, O. O., Ikubanni, P. P., Adeleke, A. A., Adediran, A. A., Adesina, O. S., Aliyu, S. J., & Olabamiji, T. S. 2020. Optimization of heat treatment parameters of medium carbon steel quenched in different media using Taguchi method and grey relational analysis. Heliyon, 6(7). https://doi.org/10.1016/j.heliyon.2020.e04444

Ahaneku, I. E., Kamal, A. R., & Ogunjirin, O. A. 2013. Effects of Heat Treatment on the Properties of Mild Steel Using Different Quenchants. Frontiers in Science, 2(6), 153–158. https://doi.org/10.5923/j.fs.20120206.04

Ahmed, A. A., Mhaede, M., Basha, M., Wollmann, M., & Wagner, L. 2015. The effect of shot peening parameters and hydroxyapatite coating on surface properties and corrosion behavior of medical grade AISI 316L stainless steel. Surface and Coatings Technology, 280, 347–358. https://doi.org/10.1016/j.surfcoat.2015.09.026

Arlingga, A. S., Somawardi, & Sugianto. 2021. Analisis Pengaruh Media Pendingin Terhadap Kekerasan Baja S45C Pada Proses Hardening-Tempering. SJoME, 3(1), 31–38.

Atmoko, N. T., Margono, & Priyambodo, B. H. 2021. Analisa Jenis Fluida Pendingin Proses Quenching pada Besi Cor Terhadap Kekerasan dan Struktur Mikro. Rotasi, 23(3), 26–30.

Azar, V., Hashemi, B., Yazdi, R., & Mahboobeh. 2010. The effect of shot peening on fatigue and corrosion behavior of 316L stainless steel in Ringer’s solution. Surface and Coatings Technology, 204(21–22), 3546–3551. https://doi.org/10.1016/j.surfcoat.2010.04.015

Ikubanni, A. A., Adediran, P. P., Agboola, A. A., Olabamiji, O. O., Ogunsola, T. S., & Ibeawuchi, O. J. 2018. Tensile Strength and Micro-Structural Behaviour of Medium Carbon Steel Quenched in Some Selected Media. International Journal of Civil Engineering and Technology (IJCIET), 9(10), 2148–2156.

Ikubanni, P. P., Adediran, A. A., Adeleke, A. A., Ajao, K. R., & Agboola, O. O. 2017. Mechanical properties improvement evaluation of medium carbon steels quenched in different media. International Journal of Engineering Research in Africa, 32, 1–10.

https://doi.org/10.4028/www.scientific.net/JERA.32.1

Iswanto, P. T., Malau, V., Priyambodo, B. H., Wibowo, T. N., & Amin, N. 2017. Effect of shot-peening on hardness and pitting corrosion rate on load-bearing implant material AISI 304. Materials Science Forum, 901 MSF, 91–96. https://doi.org/10.4028/www.scientific.net/MSF.901.91

Iswanto, P. T., Yaqin, R. I., Akhyar, & Sadida, H. M. 2020. Influence of shot peening on surface properties and corrosion resistance of implant material AISI 316L. Metalurgija, 59(3), 309–312.

Jebahi, M., Gakwaya, A., Lévesque, J., Mechri, O., & Ba, K. 2016. Robust methodology to simulate real shot peening process using discrete-continuum coupling method. International Journal of Mechanical Sciences, 107, 21–33. https://doi.org/10.1016/j.ijmecsci.2016.01.005

Kubit, A., Bucior, M., Zielecki, W., & Stachowicz, F. 2016. The impact of heat treatment and shot peening on the fatigue strength of 51CrV4 steel. Procedia Structural Integrity, 2, 3330–3336. https://doi.org/10.1016/j.prostr.2016.06.415

Lin, Q., Liu, H., Zhu, C., Chen, D., & Zhou, S. 2020. Effects of different shot peening parameters on residual stress, surface roughness and cell size. Surface and Coatings Technology, 398. https://doi.org/10.1016/j.surfcoat.2020.126054

Liu, Y. G., Li, H. M., & Li, M. Q. 2020. Roles for shot dimension, air pressure and duration in the fabrication of nanocrystalline surface layer in TC17 alloy via high energy shot peening. Journal of Manufacturing Processes, 56, 562–570. https://doi.org/10.1016/j.jmapro.2020.05.019

Liu, Y. G., Li, M. Q., & Liu, H. J. 2017. Nanostructure and surface roughness in the processed surface layer of Ti-6Al-4V via shot peening. Materials Characterization, 123, 83–90. https://doi.org/10.1016/j.matchar.2016.11.020

Li, W., & Liu, B. 2018. Experimental investigation on the effect of shot peening on contact fatigue strength for carburized and quenched gears. International Journal of Fatigue, 106, 103–113. https://doi.org/10.1016/j.ijfatigue.2017.09.015

Llaneza, V., & Belzunce, F. J. 2015. Study of the effects produced by shot peening on the surface of quenched and tempered steels: Roughness, residual stresses and work hardening. Applied Surface Science, 356, 475–485. https://doi.org/10.1016/j.apsusc.2015.08.110

Majzoobi, G. H., & Abbasi, F. 2017. On the effect of shot-peening on fretting fatigue of Al7075-T6 under cyclic normal contact loading. Surface and Coatings Technology, 328, 292–303. https://doi.org/10.1016/j.surfcoat.2017.08.067

Maleki, E., Unal, O., Reza Kashyzadeh, K., Bagherifard, S., & Guagliano, M. 2021. A systematic study on the effects of shot peening on a mild carbon steel: Microstructure, mechanical properties, and axial fatigue strength of smooth and notched specimens. Applied Surface Science Advances, 4. https://doi.org/10.1016/j.apsadv.2021.100071

Margono, Priyambodo, B. H., & Yaqin, R. I. 2021. Shot peening on AISI 304 by Various Sizes of Steel Ball Particles to Reduce Corrosion Rates. The Journal of Corrosion Science and Engineering, 23, 1–8.

Miao, H. Y., Demers, D., Larose, S., Perron, C., & Lévesque, M. 2010. Experimental study of shot peening and stress peen forming. Journal of Materials Processing Technology, 210(15), 2089–2102. https://doi.org/10.1016/j.jmatprotec.2010.07.016

Nishibata, T., & Kojima, N. 2013. Effect of quenching rate on hardness and microstructure of hot-stamped steel. Journal of Alloys and Compounds, 577(SUPPL. 1). https://doi.org/10.1016/j.jallcom.2011.12.154

Prihandoko, P., Saputra, Y. R., Sriani, T., Sunardi, & Prihandana, G. S. 2016. Effect of Time Variation on Shot peening Process to the Surface Properties of SS-316L Osteosynthesis Plate. Applied Mechanics and Materials, 842, 430–434. https://doi.org/10.4028/www.scientific.net/AMM.842.430

Priyambodo, B. H., Suhartoyo, & Slamet, S. 2020. Increased Corrosion Resistance on Cu35%Zn Surface by Shot peening Process. Journal of Physics: Conference Series, 1430(1). https://doi.org/10.1088/1742-6596/1430/1/012055

Priyambodo, B. H., Yaqin, R. I., & Nugroho, K. C. 2021. Pengaruh Perlakuan Annealing dan Shoot Peening Terhadap Kekerasan dan Struktur Mikro Pada Baja Karbon JIS S45C. Jurnal Teknologi Terapan, 7(2), 138–144.

Qu, S., Duan, C., Hu, X., Jia, S., & Li, X. 2021. Effect of shot peening on microstructure and contact fatigue crack growth mechanism of shaft steel. Materials Chemistry and Physics, 274. https://doi.org/10.1016/j.matchemphys.2021.125116

Salman, K. D., Bassam, A. A., & Frhan, I. N. 2018. Effect of Quenching Media on Mechanical Properties of Medium Carbon Steel 1030. Engineering Sciences, 26(2), 214–222.

Sreeja, V., Dinesh, P., & Patil, S. B. 2016. Study of Mechanical Properties of Steel Quenched in a

Blend of Biodegradable Oils with Quench Accelerators. IJLTEMAS, 5(5), 20–24. www.ijltemas.in

Wibowo, T. N., & Hartono, W. 2019. Pengaruh Variasi Waktu Shot peening pada Material ST 37 Terhadap Kekerasan Permukaan dan Struktur Mikro Effect of Shot peening Time Variation on ST Material 37 Against Surface Hardness and Micro Structure Shot peening Proses shot peening pada penelitian i. Prosiding Seminar Nasional Unimus 2, 431–437.

Wu, J., Wei, P., Liu, H., Zhang, B., & Tao, G. 2021. Effect of shot peening intensity on surface integrity of 18CrNiMo7-6 steel. Surface and Coatings Technology, 421. https://doi.org/10.1016/j.surfcoat.2021.127194

Wu, J., Wei, P., Liu, H., Zhang, X., He, Z., & Deng, G. 2022. Evaluation of pre-shot peening on improvement of carburizing heat treatment of AISI 9310 gear steel. Journal of Materials Research and Technology, 18, 2784–2796. https://doi.org/10.1016/j.jmrt.2022.03.163

Xiao, Z. M., Fok, W. C., & Lwin, D. T. 1993. Effects of air-blast pressure and exposure time on the shot-peening process. In Journal of Materials Processing Technology (Vol. 39).

Yaqin, R. I., Iswanto, P. T., & Maliwemu, E. U. K. 2021. Shot peening effect on surface properties and pitting corrosion resistance of biomedical structural steel aisi 316l. Metalurgija, 60(4), 249–252.

Yaqin, R. I., Iswanto, P. T., Priyambodo, B. H., & Kondi Maliwemu, E. U. 2017. Pengaruh durasi shot peening terhadap struktur mikro dan kekerasan permukaan pada AISI 316L. Seminar Nasional Teknologi Informasi Dan Kedirgantaraan (SENATIK), III, 0–4. https://doi.org/http://dx.doi.org/10.28989/senatik.v3i0.120

Zhang, J., Li, W., Wang, H., Song, Q., Lu, L., Wang, W., & Liu, Z. 2016. A comparison of the effects of traditional shot peening and micro-shot peening on the scuffing resistance of carburized and quenched gear steel. Wear, 368–369,253–257. https://doi.org/10.1016/j.wear.2016.09.029




DOI: https://doi.org/10.18196/jqt.v4i1.16170

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 Quantum Teknika : Jurnal Teknik Mesin Terapan

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Quantum Teknika : Jurnal Teknik Mesin Terapan is indexed by :

 

Office:

Editorial of Quantum Teknika, Building D, Jl. Brawijaya, Tamantirto, Kasihan, Bantul, Yogyakarta.

Telp: (0274) 387656
Fax: (0274) 387646
WA: +62896-7470-8638 (Mirza Yusuf)
Email: jqt@umy.ac.id

Creative Commons License
Quantum Teknika : Jurnal Teknik Mesin Terapan is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.