Design of Paper Foil and Laminating Machine as Lining Material for Paper Bags

Authors

  • Pongky Lubas Wahyudi Vocational Faculty, Manufacturing Technology Program/Universitas 17 Agustus 1945 Surabaya, Surabaya, Indonesia
  • Yusuf Eko Nur Cahyo Vocational Faculty, Manufacturing Technology Program/Universitas 17 Agustus 1945 Surabaya, Surabaya, Indonesia
  • Risandie Octafian Budiyanto Vocational Faculty, Manufacturing Technology Program/Universitas 17 Agustus 1945 Surabaya, Surabaya, Indonesia
  • Anita Wulandari Vocational Faculty, Agroindustry Program/Universitas 17 Agustus 1945 Surabaya, Surabaya, Indonesia https://orcid.org/0000-0003-3202-1415

DOI:

https://doi.org/10.18196/jmpm.v9i1.26117

Keywords:

Design, Foil Coating Machine, Paper Bag

Abstract

In order to enhance the contribution of MSMEs as a key driver of Indonesia’s economic growth, the development of small- to medium-scale production machines is essential. This is particularly important as MSMEs face increasing competition and more complex customer demands. This study aims to design and develop a simple production machine using CAD software and Autodesk Inventor to improve productivity and quality in the paper bag manufacturing process. Currently, production is carried out manually, resulting in limited capacity and product quality. The machine being designed serves to perform the paper gluing and rolling processes with foil lamination. The design integrates the gluing and rolling mechanisms into a single unit equipped with an automatic rotating system. This setup significantly reduces production time, thereby increasing both capacity and quality compared to the manual process. Simulation analysis of force, stress, and safety factor was carried out assuming the frame receives a load of 120 N, based on conditions close to reality. The results show a maximum Von Mises stress of 97.91 MPa and a minimum of 0 MPa. The maximum displacement is 0.5844 mm, and the minimum is 0 mm. The safety factor at the top frame section is 2.55 ul. Meanwhile, for testing under a 12 kg load, the results show a maximum Von Mises stress of 108.8 MPa, a displacement of 0.6488 mm, and a safety factor of 2.3 ul.

References

Sharma PC and Aggarwal DK, “Machine Design II,” 2014.

Sularso and K. Suga, “Dasar Dasar Perencanaan dan Pemilihan Elemen Mesin,” Jakarta, 2004.

J. C. Vieira, “Converting Operation Impact Tissue Paper Product Properties - A Review,” 2023.

A. Wisnujati and M. Yusuf, “Rancang Bangun dan Uji Kinerja Mesin Bead Roller untuk Perbaikan Bodi Kendaraan,” Rekayasa, vol. 14, no. 1, pp. 114–120, Mar. 2021, doi: 10.21107/rekayasa.v14i1.10092.

M. Rizky Firmansyah and A. Basyir, “Analisa Variasi Putaran Pada Mesin Roll Pembentuk Plat Profil Terhadap Hasil Pengerolan Plat 1 mm,” 2017.

U. Tarigan, “Pendekatan Metode DFMA (Design for Manufacture and Assembly) Pada Perancangan Produk Matras,” Talent. Conf. Ser. Energy Eng. , vol. 3, no. 2, pp. 549–555, 2020, doi: 10.32734/ee.v3i2.1041.

H. Hashimoto, P. Jeenkour, and M. Mongkolowongrojn, “Optimum winding tension and nip-load into wound webs for protecting wrinkles and slippage,” J. Adv. Mech. Des. Syst. Manuf., vol. 4, no. 1, pp. 214–225, 2010, doi: 10.1299/jamdsm.4.214.

Wu Dehui, C. Chen, Y. Xiumiao, Li Xuesong, and H. Yimin, “Optimization of taper winding tension in roll-to-roll web systems,” Text. Res. J., vol. 84, no. 20, pp. 2175–2183, 2014, doi: 10.1177/0040517514538697.

George Omura, “Mastering AutoCAD ® 2016 and AutoCAD LT ® 2016,” 2015.

Curtis Waguespack, “Mastering Autodesk ® Inventor ® 2014 and Autodesk ® Inventor LT TM 2014,” 2013.

I. W. Widhiada, “Mechanical Engineering Design Dengan Menggunakan Software Autodesk Invertor Versi 2014 dan 2017,” 2017.

A. Yarwood, “Introduction-to-autocad-2010,” 2009.

A. E. Purkuncoro, Pengenalan Computer Aided Design 2D/3D Assembly dan Animate Menggunakan Autodesk Invertor Profesional. 2019.

A. Deutscman, Machine design: theory and practice. New York: Macmillan, 1975.

R. S. Khurmi and J. K. Gupta, “A Textbook of Machine Design,” 2005.

T. V. Minh and T. T. Tung, “A Prototype of Paper Cutting Machine,” J. Appl. Eng. Sci., vol. 23, no. 1, pp. 1–14, 2025, doi: 10.5937/jaes0-46220.

Downloads

Published

2025-06-25

How to Cite

Wahyudi, P. L., Cahyo, Y. E. N., Budiyanto, R. O., & Wulandari, A. (2025). Design of Paper Foil and Laminating Machine as Lining Material for Paper Bags. JMPM (Jurnal Material Dan Proses Manufaktur), 9(1), 63–69. https://doi.org/10.18196/jmpm.v9i1.26117

Issue

Vol. 9 No. 1 (2025): Juni

Section

Articles

License

Copyright (c) 2025 Pongky Lubas Wahyudi, Yusuf Eko Nur Cahyo, Risandie Octafian Budiyanto, Anita Wulandari

Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

License

Creative Commons License


JMPM (Jurnal Material dan Proses Manufaktur) is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License. You are free to :

  1. Adapt — remix, transform, and build upon the material for any purpose, even commercially.

The licensor cannot revoke these freedoms as long as you follow the license terms, which include the following:

  • Attribution — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.

  • ShareAlike — If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.