Penggunaan Pencekam Tiga Aksis untuk Alat Bantu Pengelasan Rangka Furnitur
Main Article Content
Abstract
Distorsi logam terjadi akibat kontraksi logam yang terpapar suhu tinggi sehingga menimbulkan tarikan atau dorongan pada benda kerja. Alat bantu berupa pencekam banyak digunakan pada proses pengelasan untuk mencegah distorsi pada logam. Pencekam tiga aksis mampu melakukan proses pencekaman ketiga aksis sekaligus. Proses penggunaan pencekam jenis ini sangat bermanfaat untuk proses pengelasan rangka furnitur. Pencekam ini digunakan untuk meningkatkan efisiensi produksi rangka kursi. Penelitian ini untuk mengkaji pemanfaatan pencekam tiga sumbu untuk menahan fenomena distorsi akibat kenaikan suhu proses pengelasan, dan peningkatan produktifitas waktu proses penyambungan dengan variasi arus pengelasan 50 Ampere dan 60 Ampere. Kinerja pencekam mampu mempercepat waktu proses 19% dan menekan biaya pembuatan produk rangka sebesar 43,74%.
Metal distortion occurs due to contractions of metal exposed to high temperatures that cause pulling or pushing on the work piece. Three-axis fixtures are widely used in welding process to minimize metal distortion. Three-axis fixture is capable of holding the three axis simultaneously, so it is very useful for the welding furniture frames, and can improve the efficiency of chair frame production. This study is to examine the use of three-axis fixture to withstand the phenomenon of distortion due to the increase in temperature of welding process at welding current of 50 Amperes and 60 Amperes, and decrease production time of the joining process. The fixture performance was able to speed up processing time by 19% and reduced the cost of frame production by 43.74%.
Article Details
License
JMPM (Jurnal Material dan Proses Manufaktur) is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License. You are free to :
- Share — copy and redistribute the material in any medium or format
- Adapt — remix, transform, and build upon the material for any purpose, even commercially.
The licensor cannot revoke these freedoms as long as you follow the license terms, which include the following:
-
Attribution — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
-
ShareAlike — If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.
References
S. Ahmaden, “Rancang Bangun Alat Penepat untuk Pengelasan pada Pagar Ranjang Rumah Sakit Ekonomis dengan Metode Meja Putar (Proses Pembuatan),” Politeknik Negeri Sriwijaya, 2014.
H. Prassetiyo, I. R. Ramdhan, J. T. Industri, F. T. Industri, J. P. H. H. Mustofa, and N. Bandung, “Bidang Teknik Mesin Rancangan Welding Fixture Pembuatan Rangka Produk Kursi Prosiding Seminar Nasional Teknoin 2012 ISBN No . 978-979-96964-3-9,” no. November, pp. 116–123, 2012.
S. S. Pachbhai and L. P. Raut, “A Review on Design of Fixtures,” Int. J. Eng. Res. Gen. Sci., vol. 2, no. 2, pp. 126–146, 2014.
A. I. Komara and F. Syaleh, “Studi Perancangan Welding Fixture untuk Pengelasan Bevel Gear Support dan Motor Drive Support pada Transformator,” J. Teknol. dan Rekayasa Manufaktur, vol. 02, pp. 1–8, 2006.
E. G. Hoffman, Jig and Fixture Design Fourth Edition, Fourth. New York: Delmar Publisher Inc, 1996.
A. Syadda and Fusito, “PERANCANGAN DAN PEMBUATAN ALAT BANTU PEGANG ( FIXTURE ) UNTUK PROSES PENGELASAN SAMBUNGAN-T Anhara Syadda dan Fusito Jurusan Teknik Mesin Fakultas Teknik Universitas Sriwijaya Jl . Raya Palembang - Prabumulih Km 32 , Inderalaya ( OI ) Telp / Fax . ( 0711,” Universitas Sriwijaya, 2020.
S. N. Shinde, S. Kshirsagar, A. Patil, T. Parge, and R. Lomte, “Design of Welding Fixtures and Positiners,” Int. J. Eng. Res. Gen. Sci., vol. 2, no. 5, pp. 681–689, 2014.
D. McBee, “WELDING CLAMP,” US 6,349,869 B1, 2002.
Yatno, “Kebutuhan Pembuatan Furnitur Kombinasi Logam dan Kayu,” Banjarnegara, 2019.
M. Vural, “The effect of welding fixtures on welding distortions,”June, 2014.