Analisis Desain Tie Rod Alat Penukar Kalor Shell dan Tube Berdasarkan TEMA Standard

Krisdiyanto Krisdiyanto, Rahmad Kuncoro Adi

Abstract


Heat exchanger adalah peralatan yang digunakan untuk memindahkan energi kalor tanpa disertai perpindahan massa. Perancangan heat exchanger harus memenuhi standar yang telah ditentukan. Salah satu standard yang digunakan yaitu dokumen yang dikeluarkan oleh TEMA. Standar tersebut masih belum optimal sehingga perlu dilakukan optimasi pada komponennya. Salah satu komponen heat exchanger yaitu tie rod. Komponen tersebut dianalisis menggunakan metode finite element. Simulasi pemberian tekanan pada geometri dapat dilakukan menggunakan platform SimScale. Tekanan yang dipakai sebagai beban dapat dipakai untuk menghitung von mises pada shell. Hasil penelitian ini menunjukkan nilai overdesign pada komponen tie rod yaitu 475,19%.

 

Heat exchanger is an equipment that is used to transfer heat energy without mass transfer. The design of the heat exchanger must meet predetermined standards. One of the standards used is the document issued by TEMA. The standard is still not optimal so it needs to be optimized for its components. One component of the heat exchanger is tie rod. The components were analyzed using the finite element method. Simulations of applying stress to the geometry can be done using the SimScale platform. Pressure used as a load can be used to calculate von mises on the shell. The results of this study indicate the value of overdesign on the tie rod component is 475.19%.


Keywords


finite element, tegangan, overdesign

Full Text:

PDF

References


D. P. Sekulic, “A reconsideration of the definition of a heat exchanger,” Int. J. Heat Mass Transf., vol. 33, no. 12, pp. 2748–2750, 1990, doi: 10.1016/0017-9310(90)90209-D.

K. D. Shirode, D. S. Rane, and M. Y. Naik, “Comparison of Design and Analysis of Tubesheet Thickness by Using UHX Code of ASME and TEMA Standard,” pp. 96–108, 2013.

E. Ozden and I. Tari, “Shell side CFD analysis of a small shell-and-tube heat exchanger,” Energy Convers. Manag., vol. 51, no. 5, pp. 1004–1014, 2010, doi: 10.1016/j.enconman.2009.12.003.

F. T. Mizutani, F. L. P. Pessoa, E. M. Queiroz, S. Hauan, and I. E. Grossmann, “Mathematical programming model for heat-exchanger network synthesis including detailed heat-exchanger designs. 2. Network synthesis,” Ind. Eng. Chem. Res., vol. 42, no. 17, pp. 4019–4027, 2003, doi: 10.1021/ie020965m.

S. Xu and W. Wang, “Numerical investigation on weld residual stresses in tube to tube sheet joint of a heat exchanger,” Int. J. Press. Vessel. Pip., vol. 101, pp. 37–44, 2013, doi: 10.1016/j.ijpvp.2012.10.004.

James R. Farr and M. H. Jawad, Guidebook for the Design of ASME Section VIII Pressure Vessel Second Edition, vol. 53, no. 9. 2013.

Q. Liang, Performance-Based Optimization of Structures: Theory and Applications. 2007.

L. Yang, C. Weinberger, and Y. T. Shah, “Finite element analysis on horizontal vessels with saddle supports,” Comput. Struct., vol. 52, no. 3, pp. 387–395, 1994, doi: 10.1016/0045-7949(94)90224-0.

Khurmi.R.S and Gupta.J.K, A Textbook of Machine design, no. I. 2005.

W. L. Oberkampf, T. G. Trucano, and C. Hirsch, “Verification, validation, and predictive capability in computational engineering and physics,” Appl. Mech. Rev., vol. 57, no. 1–6, pp. 345–384, 2004, doi: 10.1115/1.1767847.

H. Franck and D. Franck, Forensic engineering fundamentals. 2012.

W. A. Beyers, A. Zapke, and G. Venter, “Improved Cover Type Header Box Design Procedure,” no. December, 2015.




DOI: https://doi.org/10.18196/jmpm.v4i1.9348

Refbacks

  • There are currently no refbacks.


 

Editorial Office :

JMPM (Jurnal Material dan Proses Manufaktur)

Department of Mechanical Engineering, Faculty of Engineering, Universitas Muhammadiyah Yogyakarta.

Jl. Brawijaya Tamantirto Kasihan Bantul 55183 Indonesia

Email: jmpm@umy.ac.id

 (62)274-387656     (62)274-387656