Analisis Kekuatan Mekanik pada Struktur Cooling Tank Section Untai FASSIP-03 NT Berbasis Simulasi Software

Authors

  • Dedy Haryanto Pusat Riset Teknologi dan Keselamatan Reaktor Nuklir- Badan Riset dan Inovasi Nasional
  • Giarno Giarno Pusat Riset dan Teknologi Reaktor Keselamatan dan Keamanan Nuklir, Badan Riset dan Inovasi Nasional (BRIN)
  • Adhika Enggar Pamungkas Pusat Riset dan Teknologi Reaktor Keselamatan dan Keamanan Nuklir, Badan Riset dan Inovasi Nasional (BRIN)
  • Ainur Rosidi Pusat Riset dan Teknologi Reaktor Keselamatan dan Keamanan Nuklir, Badan Riset dan Inovasi Nasional (BRIN)
  • Gregorius Bambang Heru Kusnugroho Pusat Riset dan Teknologi Reaktor Keselamatan dan Keamanan Nuklir, Badan Riset dan Inovasi Nasional (BRIN)
  • Mulya Juarsa Pusat Riset dan Teknologi Reaktor Keselamatan dan Keamanan Nuklir, Badan Riset dan Inovasi Nasional (BRIN)

DOI:

https://doi.org/10.18196/st.v25i1.13470

Keywords:

CTS, kekuatan mekanik, tegangan mekanik, translational displacement, FASSIP-03 NT

Abstract

Untai Fasilitas Simulasi Sistem Pasif-03 Nanobubble Transparent (FASSIP-03 NT) mulai didesain pada tahun 2021. Komponen pada untai FASSIP-03 NT terdiri dari Heating Tank Section (HTS) dan Cooling Tank Section (CTS) yang dilengkapi dengan Helical Heat Exchanger, Pyrex Glass Tube dan sistem pemipaan. CTS berfungsi sebagai komponen untuk mensimulasikan penukar kalor dari teras reaktor nuklir. Pengujian secara simulasi dan analisisnya dilakukan untuk mengetahui kekuatan mekanik terdiri dari tegangan mekanik dan translational displacement pada desain komponen CTS. Hasil pengujian secara simulasi diperoleh tegangan mekanik maksimal sebesar 1,61 x 108 N/m2 lebih kecil daripada yield strength material stainless steel 304 sebesar 1,73 x 108 N/m2. Translational displacement yang terjadi sebesar 3,04 mm pada bagian sisi belakang CTS. Hasil pengujian secara simulasi dan analisisnya menunjukkan bahwa desain CTS dapat dipabrikasi dan aman digunakan sebagai penukar kalor pada untai FASSIP-03 NT.

References

Anonim. (2011), Yield strength-strength (mechanics) of materials strength/mechanics of materials, http://www.engineersedge.com, December 1st.

Antariksawan A., R. (2000). Accident analysis of PWR station blackout with pump seal leak using Melcor 1.8. 4, Proceeding of the Sixth: Seminar on Technology and Safety of Nuclear Power Plants and Nuclear Facilities, 1 November 2000.

Antariksawan, A. R., Widodo, S., Juarsa, M., Giarno, Kusuma, M. H., & Putra, N. (2018). Preliminary investigation of natural circulation stability in FASSIP-01 experimental facility using RELAP5 code, AIP Conference Proceedings, 2001(1). https://doi.org/10.1063/1.5050011

Antariksawan, A. R., Juarsa, M., Giarno, Kusuma, M. H., & Putra, N. (2018). Simulation of operational conditions of FASSIP-02 natural circulation cooling system experimental loop. Jurnal Sains dan Teknologi Nuklir Indonesia (Indonesian Journal of Nuclear Science and Technology, 19(1), 41-52. http://doi.org/10.17146/jstni.2018.19.1.4036

Bauer Energy Design, (2021), http://www.nanobubbles.com/, accessed on July 24th.

Byrne, R., C. (1988). Standard of the tubular exchanger manufacturers association, tubular exchanger manufacturers association, (TEMA) Inc, 25 North Broadway Tarrytown, New York 10591 seventh edition.

Daugherty, R. L. (1989). Fluid mechanics with engineering applications. McGraw-Hill.

Haryanto, D., Giarno, G., Kusnugroho, G. B. H, & Juarsa, M. (2020). Analisis kekuatan mekanik main steam generator pada fasilitas PASCONEL, Prosiding Seminar Nasional Teknologi Energi Nuklir 2020 (ISSN:2355-7524), 18 November 2020.

Haryanto, D., Giarno, G., Witoko, J. P., Hatmoko, S., Santosa, K., Juarsa, M., Kusuma, M. H., Antariksawan, A. R., & Putra, N. (2018). Analisis kekuatan mekanik struktur dengan penambahan beban komponen FASSIP-02 menggunakan software CATIA. Prosiding Seminar Nasional Teknologi Energi Nuklir Tahun 2018, ISSN: 2355-7524.

Haryanto, D., Giarno, G., Witoko, J. P., Hatmoko, S., Santosa, K., Juarsa, M., Kusuma, M. H., Antariksawan, A. R., & Putra, N. (2018). Analisis kekuatan mekanik water cooling tank pada fasilitas uji untai PASSIF-02 menggunakan CATIA. Jurnal Ilmiah Teknik Mesin POROS, 16(1), 79-85. http://doi.org/10.24912/poros.v16i1.6296

Haryanto, D., Rosidi, A., Kusnugroho, G. B. H., Giarno, G., Witoko, J. P. (2020). Analisis kekuatan mekanik desain bejana molecular sieve. Sigma Epsilon, 24(1), 44-53. http://doi.org/10.17146/sigma.2020.24.1.5821

IAEA, (2009), Passive safety system and natural circulation in water cooled nuclear power plants, IAEA-TECDOC-1624.

Juarsa, M., Antariksawan, A. R., Kusuma, M. H., Haryanto, D., & Putra, N. (2018). Estimation of natural circulation flow based on temperature in the FASSIP-02 large-scale test loop facility, IOP Conf. Ser. Earth Environ. Sci., 105(1). http://doi.org/10.1088/1755-1315/105/1/012091.

Juarsa, M., Antariksawan, A. R., Kusuma, M. H., Haryanto, D., & Putra, N. (2019). Preliminary investigation on natural circulation flow using CFD and calculation base on experimental data pre-FASSIP-02. Journal of Physics: Conference Series, 1198(2), [022073]. http://doi.org/10.1088/1742-6596/1198/2/022073.

Juarsa, M., Haryanto, D., Rosidi, A., Kusnugroho, G. B. H., & Giarno, G. (2011). Studi eksperimental laju aliran massa air berdasarkan perubahan sudut kemiringan untai pada kasus sirklasi alamiah menggunakan untai sirklasi alamiah (USSA-FT01). Jurnal Material dan Energi Indonesia, Jurusan Fisika FMIPA, Universitas Padjajaran, 1, 22-30.

Kusuma, M. H., Putra, N., Ismawanti, S., & Widodo, S. (2017). Simulation of wickless-heat pipe as passive cooling system in nuclear spent fuel pool using RELAP5/MOD3.2. International Journal on Advanced Science, Engineering and Information Technology, 7(3), 836-842. https://doi.org/10.18517/ijaseit.7.3.2144

Menteri Ketenagakerjaan Republik Indonesia. (2016). Keselamatan dan kesehatan kerja bejana tekan dan tangki timbun, Peraturan Menteri Ketenagakerjaan Republik Indonesia Nomor 37 Tahun 20.

Moleaer. (2021). https://www.moleaer.com/nanobubbles, accessed on July 24th,

Pinem, M. D., (2009). CATIA si jago desain tiga dimensi. LinguaKata.

Sun, D. C., Li, Y., Xi, Z., Zan, Y. F., Li, P. Z., & Zhuo, W. B. (2017). Experimental evaluation of safety performance of emergency passive residual heat removal system in HPR1000. Nuclear Engineering and Design, 318, 54-60. https://doi.org/10.1016/j.nucengdes.2017.04.003

Tjahjono, H. (2017). Comprehensive prediction of thermosyphon characteristics in reactor passive cooling system simulation loop FASSIP-01. Atom Indonesia, 43(3), 157-166.

https://doi.org/10.17146/aij.2017.777

Wang, M., Tian, W., Qiu, S., Su, G., & Zhang, G. (2013). An evaluation of designed passive core makeup tank (CMT) for China pressurized reactor (CPR1000). Annals of Nuclear Energy, 56, 81-86. https://doi.org/10.1016/j.anucene.2013.01.010

Wang, Y. (2013). Preliminary study for the passive containment cooling system analysis of the advanced PWR. Energy Procedia, 39, 240–247. https://doi.org/10.1016/j.egypro.2013.07.210

Downloads

Published

2022-05-17

How to Cite

Haryanto, D., Giarno, G., Pamungkas, A. E., Rosidi, A., Kusnugroho, G. B. H., & Juarsa, M. (2022). Analisis Kekuatan Mekanik pada Struktur Cooling Tank Section Untai FASSIP-03 NT Berbasis Simulasi Software. Semesta Teknika, 25(1), 24–32. https://doi.org/10.18196/st.v25i1.13470

Issue

Vol. 25 No. 1 (2022): MEI 2022

Section

Articles

License


Semesta Teknika is licensed under a Creative Commons Attribution 4.0 International License.

Authors who publish with this journal agree to the following terms:

  • Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
  • Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
  • Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).