Grain Size Variations of Reclaimed CO2 Sand Mold on Hardness and Metal Surface Roughness
DOI:
https://doi.org/10.18196/jmpm.v7i2.17547Keywords:
CO2 waste moulding, Reclaimed, Grain size, Surface roughness.Abstract
Studies on reclaiming CO2 sand mould waste have the opportunity to increase productivity. This research was conducted to learn further about the potential of reclaimed CO2 sand moulds. The effect of the grain size of the reclaimed CO2 sand mould on the hardness and metal surface roughness was analyzed. In addition, a comparison of casting quality analysis was carried out between products using new sand and reclaimed CO2 sand moulds. The CO2 sand moulds were crushed and then sieved using 12, 25 and 40 mesh sieves. The sand waste grains were reclaimed through a detergent washing process. SEM-EDS characterization was carried out to determine the elements contained. The hardness of the casting product was tested using the Rockwell method with a load of 981 N. Meanwhile, the metal surface roughness was characterized through the Roughness Test and visual identification using the JIS 82 standard. Based on the results of the SEM-EDS characterization, the three variations of the reclaimed CO2 sand have the potential to be reused. The quality of the hardness and metal surface roughness of the reclaimed CO2 sand with 25 mesh size variation is close to the quality of the casting product using a new sand mould.References
D. Haryono, “Pengaruh Jenis Pasir Cetakan Terhadap Produk Pengecoran Aluminium Dengan Metode Lost Foam Casting,” Universitas Muhammadiyah Surakarta, 2019.
J. Mitterpach, E. Hroncov, J. Ladomerský, and K. Balco, “Environmental evaluation of grey cast iron via life cycle assessment,” J. Clean. Prod. J., vol. 148, pp. 324–335, 2017, doi: 10.1016/j.jclepro.2017.02.023.
M. M. Khan, M. Singh, S. M. Mahajani, G. N. Jadhav, and S. Mandre, “Reclamation of used Green Sand in small scale foundries Authors:,” J. Mater. Process. Tech., pp. 1–35, 2018, doi: 10.1016/j.jmatprotec.2018.01.005.
R. Siddique and G. Singh, “Resources , Conservation and Recycling Utilization of waste foundry sand ( WFS ) in concrete manufacturing,” "Resources, Conserv. Recycl., vol. 55, no. 11, pp. 885–892, 2011, doi: 10.1016/j.resconrec.2011.05.001.
A. Coz, J. R. Viguri, and A. Andrés, “Recycling of foundry by-products in the ceramic industry : Green and core sand in clay bricks,” Constr. Build. Mater., vol. 27, no. 1, pp. 97–106, 2012, doi: 10.1016/j.conbuildmat.2011.08.022.
G. S. Patange, M. P. Khond, H. J. Rathod, and K. B. Chhadva, “Investigation of foundry waste sand reclamation process for small and medium scale indian foundry,” Int. J. Ind. Eng. Technol., vol. 3, no. 1, pp. 1–6, 2013.
A. Ghosh, “Modern Sand Reclamation Technologies for Economy , Environment Friendliness and Energy Efficiency,” in Transactions of 61st Indian Foundry Congress, 2013, pp. 1–5.
M. Stachowicz and K. Granat, “Possibilities of reclamation microwave-hardened molding sands with water glass,” Arch. Metall. Mater., vol. 59, no. 2, pp. 757–760, 2014, doi: 10.2478/amm-2014-0127.
D. F. Undayat, C. Ruskandi, and M. N. Hidajatullah, “Perancangan Sistem Daur Ulang Pasir Pada Industri Pengecoran Logam Skala Kecil Untuk Peningkatan Efisiensi Biaya Dan Pengurangan Limbah,” J. Teknol. Terap. |, vol. 4, no. 1, pp. 55–62, 2018.
D. R. Patel, M. V. Oza, and M. V. Pandya, “Reclamation of Sodium Silicate Bonded CO 2 Sand by Detergent Wash Method,” Int. J. Eng. Technol. Manag. Appl. Sci., vol. 3, no. Special Issue, pp. 156–161, 2015.
W. A. Saputra, M. Balfas, and M. H. Asiri, “Analisis Kekerasan Coran Aluminium dengan Variasi Besar Butir Pasir Cetak,” Teknologi, vol. 18, no. 1, pp. 1–5, 2018.
N. Ahmadi, “Effects Of Grains Size And Sandblasting Duration To The Surface Hardness Of The Casting Product,” in Prosiding Seminar Nasional Teknologi Informasi dan Kedirgantaraan : Transformasi Teknologi untuk Mendukung Ketahanan Nasional, 2018, vol. IV, pp. 1–6.
M. I. Z. Muttahar et al., “Pengaruh Cetakan Pasir Daur Ulang Berpengikat Waterglass Terhadap Permukaan Logam Hasil Pengecoran,” Flywheel J. Tek. Mesin Untirta, vol. IV, no. 1, pp. 39–44, 2018.
S. I. Khasanah, N. R. Sesunan, and H. Abdillah, “Study of the Reclamation of Waste CO 2 Moulding Sand in Foundry Industry,” Int. J. Emerg. Trends Eng. Res., vol. 8, no. 9, pp. 5454–5459, 2020.
S. J. Siagian, I. K. Gede, C. Istri, and P. Kusuma, “Pengaruh Permeabilitas Cetakan Pasir dan Penambahan Silikon ( Si ) pada Proses Pengecoran Terhadap Kekerasan , Porositas dan Struktur Mikro Alumunium Silikon ( Al-Si ),” J. Ilm. Tek. Desain Mek., vol. 6, no. 4, pp. 305–310, 2017.
Sigit Gunawan and Sigit Budi Hartono, “Variasi Ukuran Pasir Cetak terhadap Kekerasan dan Kekuatan Tarik Coran Scrap Piston Sepeda Motor,” Tek. Mesin, vol. 15, no. 1, pp. 10–20, 2015.
Downloads
Additional Files
Published
How to Cite
Issue
Section
License
License
JMPM (Jurnal Material dan Proses Manufaktur) is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License. You are free to :
- Share — copy and redistribute the material in any medium or format
- Adapt — remix, transform, and build upon the material for any purpose, even commercially.
The licensor cannot revoke these freedoms as long as you follow the license terms, which include the following:
-
Attribution — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
-
ShareAlike — If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.
