The Analysis of Comparison Electrical Power Measurement on LED Lamps

Authors

  • Prisma Megantoro (SCOPUS ID: 57201736900), Universitas Gadjah Mada
  • Geston Bakti Muntoha Universitas Gadjah Mada
  • Kunal Kunal Indraprastha University
  • Phong Thanlr Nguyen Ho Chi MinhCity Open University
  • Elsaved Helmy National Institute of oceanography and fisheries

DOI:

https://doi.org/10.18196/jrc.1425

Abstract

 


Abstract— This study uses 2 variations of the value of the DC 12V LED lamp power that is 12W and 15W with 3 different brands of lamp variations. Measurement of input voltage and current is carried out using a Krisbow KW06-490 DC clampmeter that has been calibrated as a standard measuring instrument and a Krisbow KW06-491 DC clampmeter that has not been calibrated as a test gauge 1 and a Multimeter Viper DT830B that has not been calibrated as a test gauge 2. Data the current and input voltage between each lamp and different lamp brands are used to calculate the value of the test lamp power and then compare it.

The big conclusion from this study was found that the error value between the value of the test power or the use of DC 12V LED lamps with 12W written power on R, S, and T brand lamps was ± 51.67%, ± 70.75%, ± 61.33 %. In 15W lamps the brands R, S, and T were ± 7.20%, ± 0.53%, ± 8.27%.

References

O. Caumont, P. Le Moigne, C. Rombaut, X. Muneret, and P. Lenain, “Energy gauge for lead-acid batteries in electric vehicles,” IEEE Trans. Energy Convers., vol. 15, no. 3, pp. 354–360, 2000.

B. Szabados and A. Mihalcea, “Design and implementation of a calorimetric measurement facility for determining losses in electrical machines,” IEEE Trans. Instrum. Meas., vol. 51, no. 5, pp. 902–907, 2002.

C. Landi, M. Luiso, and N. Pasquino, “A Remotely Controlled Onboard Measurement System for Optimization of Energy Consumption of Electrical Trains,” IEEE Trans. Instrum. Meas., vol. 57, no. 10, pp. 2250–2256, Oct. 2008.

A. M. Yassine, T. M. Chen, and M. Bordelon, “Resistance transients in Al-based thin films and activation energy measurements,” IEEE Trans. Electron Devices, vol. 45, no. 11, pp. 2375–2378, 1998.

A. D. Femine, D. Gallo, C. Landi, and M. Luiso, “Advanced Instrument For Field Calibration of Electrical Energy Meters,” IEEE Trans. Instrum. Meas., vol. 58, no. 3, pp. 618–625, Mar. 2009.

Yonghua Cheng, “Assessments of Energy Capacity and Energy Losses of Supercapacitors in Fast Charging–Discharging Cycles,” IEEE Trans. Energy Convers., vol. 25, no. 1, pp. 253–261, Mar. 2010.

S. G. Ghalamestani, T. G. D. Hilgert, L. Vandevelde, J. J. J. Dirckx, and J. A. A. Melkebeek, “Magnetostriction Measurement by Using Dual Heterodyne Laser Interferometers,” IEEE Trans. Magn., vol. 46, no. 2, pp. 505–508, Feb. 2010.

M. J. Moser, T. Bretterklieber, H. Zangl, and G. Brasseur, “Strong and weak electric field interfering: Capacitive icing detection and capacitive energy harvesting on a 220-kV high-voltage overhead power line,” IEEE Trans. Ind. Electron., vol. 58, no. 7, pp. 2597–2604, 2011.

G. Bucci, E. Fiorucci, F. Ciancetta, D. Gallo, C. Landi, and M. Luiso, “Embedded power and energy measurement system based on an analog multiplier,” IEEE Trans. Instrum. Meas., vol. 62, no. 8, pp. 2248–2257, 2013.

C. L. Holloway et al., “Broadband Rydberg atom-based electric-field probe for SI-traceable, self-calibrated measurements,” IEEE Trans. Antennas Propag., vol. 62, no. 12, pp. 6169–6182, 2014.

S. V. Gubbi and B. Amrutur, “All Digital Energy Sensing for Minimum Energy Tracking,” IEEE Trans. Very Large Scale Integr. Syst., vol. 23, no. 4, pp. 796–800, Apr. 2015.

F. Adamo, F. Attivissimo, G. Cavone, A. Di Nisio, and M. Spadavecchia, “Channel characterization of an open source energy meter,” IEEE Trans. Instrum. Meas., vol. 63, no. 5, pp. 1106–1115, 2014.

D. Lindenthaler and G. Brasseur, “Signal-Bandwidth Evaluation for Power Measurements in Electric Automotive Drives,” IEEE Trans. Instrum. Meas., vol. 64, no. 6, pp. 1336–1343, 2015.

P. C. Dias, F. J. O. Morais, M. B. de Morais Franca, E. C. Ferreira, A. Cabot, and J. A. Siqueira Dias, “Autonomous Multisensor System Powered by a Solar Thermoelectric Energy Harvester With Ultralow-Power Management Circuit,” IEEE Trans. Instrum. Meas., vol. 64, no. 11, pp. 2918–2925, Nov. 2015.

Y. Tsunoda et al., “A Small-Size Energy-Harvesting Electric Power Sensor for Implementing Existing Electrical Appliances Into HEMS,” IEEE Sens. J., vol. 16, no. 2, pp. 457–463, 2016.

N. Alatawneh and P. Pillay, “Calibration of the Tangential Coil Sensor for the Measurement of Core Losses in Electrical Machine Laminations,” IEEE Trans. Energy Convers., vol. 31, no. 2, pp. 413–423, 2016.

B. Qi, X. Zhao, and C. Li, “Methods to reduce errors for DC electric field measurement in oil-pressboard insulation based on Kerr-effect,” IEEE Trans. Dielectr. Electr. Insul., vol. 23, no. 3, pp. 1675–1682, 2016.

C. Trigona, B. Andò, S. Baglio, R. La Rosa, and G. Zoppi, “Sensors for Kinetic Energy Measurement Operating on ‘Zero-Current Standby,’” IEEE Trans. Instrum. Meas., vol. 66, no. 4, pp. 812–820, 2017.

W. Yao, Y. Zhang, Y. Liu, M. J. Till, and Y. Liu, “Pioneer design of non-contact synchronized measurement devices using electric and magnetic field sensors,” IEEE Trans. Smart Grid, vol. 9, no. 6, pp. 5622–5630, 2018.

I. S. Kwon, J. Y. Na, H. Y. Lee, and B. W. Lee, “Determination of Threshold Electric Field for PPLP Specimen in Liquid Nitrogen Based on the Measurement of Electrical Conductivity,” IEEE Trans. Appl. Supercond., vol. 28, no. 3, pp. 1–4, 2018.

W. Liu, C. Tan, X. Dong, F. Dong, and Y. Murai, “Dispersed Oil-Water Two-Phase Flow Measurement Based on Pulse-Wave Ultrasonic Doppler Coupled with Electrical Sensors,” IEEE Trans. Instrum. Meas., vol. 67, no. 9, pp. 2129–2142, 2018.

S. Chamanian, S. Baghaee, H. Ulusan, O. Zorlu, E. Uysal-Biyikoglu, and H. Kulah, “Implementation of Energy-Neutral Operation on Vibration Energy Harvesting WSN,” IEEE Sens. J., vol. 19, no. 8, pp. 3092–3099, 2019.

G. Crotti et al., “Pantograph-To-OHL Arc: Conducted Effects in DC Railway Supply System,” 9th IEEE Int. Work. Appl. Meas. Power Syst. AMPS 2018 - Proc., vol. 68, no. 2, pp. 3861–3870, 2018.

M. Raeiszadeh and F. Taghipour, “Microplasma UV lamp as a new source for UV-induced water treatment: Protocols for characterization and kinetic study,” Water Res., vol. 164, p. 114959, 2019.

S. Mehran, M. Nikian, M. Ghazi, H. Zareiforoush, and I. Bagheri, “Experimental investigation and energy analysis of a solar-assisted fluidized-bed dryer including solar water heater and solar-powered infrared lamp for paddy grains drying,” Sol. Energy, vol. 190, no. March, pp. 167–184, 2019.

W. Do et al., “Effect of flash lamp annealing on electrical activation in boron-implanted polycrystalline Si thin films,” Mater. Res. Bull., vol. 58, pp. 164–168, 2014.

C. De Santi et al., “Failure causes and mechanisms of retrofit LED lamps,” Microelectron. Reliab., vol. 55, no. 9–10, pp. 1765–1769, 2015.

M. Cai et al., “Step-stress accelerated testing of high-power LED lamps based on subsystem isolation method,” Microelectron. Reliab., vol. 55, no. 9–10, pp. 1784–1789, 2015.

C. Stegner, M. Dalsass, P. Luchscheider, and C. J. Brabec, “Monitoring and assessment of PV generation based on a combination of smart metering and thermographic measurement,” Sol. Energy, vol. 163, no. February, pp. 16–24, 2018.

W. L. Rodrigues Junior, F. A. S. Borges, A. F. da S. Veloso, R. de A. L. Rabêlo, and J. J. P. C. Rodrigues, “Low voltage smart meter for monitoring of power quality disturbances applied in smart grid,” Measurement, vol. 147, p. 106890, 2019.

S. Sureshkumar et al., “Utilization of eddy current flow meter for sodium flow measurement in FBRs,” Nucl. Eng. Des., vol. 265, pp. 1223–1231, 2013.

R. W. Herschy, “The uncertainty in a current meter measurement,” Flow Meas. Instrum., vol. 13, no. 5–6, pp. 281–284, 2002.

M. M. Othman, M. H. Ahmed, and M. M. A. Salama, “A novel smart meter technique for voltage and current estimation in active distribution networks,” Int. J. Electr. Power Energy Syst., vol. 104, no. February 2018, pp. 301–310, 2019.

D. B. Avancini, J. J. P. C. Rodrigues, S. G. B. Martins, R. A. L. Rabêlo, J. Al-Muhtadi, and P. Solic, “Energy meters evolution in smart grids: A review,” J. Clean. Prod., vol. 217, pp. 702–715, 2019.

F. Abate, M. Carratù, C. Liguori, and V. Paciello, “A low cost smart power meter for IoT,” Meas. J. Int. Meas. Confed., vol. 136, pp. 59–66, 2019.

G. van de Kaa, T. Fens, J. Rezaei, D. Kaynak, Z. Hatun, and A. Tsilimeni-Archangelidi, “Realizing smart meter connectivity: Analyzing the competing technologies Power line communication, mobile telephony, and radio frequency using the best worst method,” Renew. Sustain. Energy Rev., vol. 103, no. January 2017, pp. 320–327, 2019.

F. Ni, P. H. Nguyen, J. F. G. Cobben, H. E. Van den Brom, and D. Zhao, “Three-phase state estimation in the medium-voltage network with aggregated smart meter data,” Int. J. Electr. Power Energy Syst., vol. 98, no. October 2017, pp. 463–473, 2018.

Y. Wang, H. Qiu, Y. Tu, Q. Liu, Y. Ding, and W. Wang, “A review of smart metering for future Chinese grids,” Energy Procedia, vol. 152, pp. 1194–1199, 2018.

N. A. Funde, M. M. Dhabu, A. Paramasivam, and P. S. Deshpande, “Motif-based association rule mining and clustering technique for determining energy usage patterns for smart meter data,” Sustain. Cities Soc., vol. 46, no. November 2018, p. 101415, 2019.

C. Stegner, O. Glaß, and T. Beikircher, “Comparing smart metered, residential power demand with standard load profiles,” Sustain. Energy, Grids Networks, vol. 20, p. 100248, 2019.

Downloads

Published

2020-03-30

Issue

Vol. 1 No. 4 (2020): July

Section

Articles

License

Authors who publish with this journal agree to the following terms: 

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

 

This journal is based on the work at https://journal.umy.ac.id/index.php/jrc under license from Creative Commons Attribution-ShareAlike 4.0 International License. You are free to:

  1. Share – copy and redistribute the material in any medium or format.
  2. Adapt – remix, transform, and build upon the material for any purpose, even comercially.

The licensor cannot revoke these freedoms as long as you follow the license terms, which include the following:

  1. Attribution. You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
  2. ShareAlike. If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.
  3. No additional restrictions. You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.

 

• Creative Commons Attribution-ShareAlike (CC BY-SA)

Creative Commons License
JRC is licensed under an International License