The Design of Tachometer Contact and Non-Contact Using Microcontroller

Authors

  • Tatiya Padang Tunggal Universitas Muhammadiyah Yogyakarta
  • Lailicia Anggi Kirana Department of Electrical Engineering, Universitas Muhammadiyah Yogyakarta, Yogyakarta, Indonesia
  • Afif Zuhri Arfianto Program Studi Teknik Otomasi, Jurusan Kelistrikan Kapal, Politeknik Perkapalan Negeri Surabaya
  • Elsayed T.Helmy National Institute of oceanography and fisheries, Alexandria, Egypt
  • Farhad Waseel Department of mathematics, Kabul University, Kabul, Afghanistan

DOI:

https://doi.org/10.18196/jrc.1315

Abstract

Calibration is required for various kinds of tools from kitchen tools such as stirrers or mixers to medical tools such as temperature calibration, ECG, blood pressure, and other instrumentation tools to be according to the required standards. In medical devices, a digital tachometer has been used as a calibration support device to measure the speed of objects that rotate in RPM on the centrifuge. Some medical devices are calibrated in km/hour, for example, the ergo cycle and treadmill. Two different devices or a conversion from RPM to km/hour are required. The research aimed to design a measurement device that performed calibration of devices with different units, namely tachometer that can be used to measure speed in RPM and km/hr. Based on the research objective, a tool was made to measure the motor's rotational speed using the E18-D80NK sensor, microcontroller, and LCD without touching the object being measured.

Author Biographies

Tatiya Padang Tunggal, Universitas Muhammadiyah Yogyakarta

Electrical Engineering

Lailicia Anggi Kirana, Department of Electrical Engineering, Universitas Muhammadiyah Yogyakarta, Yogyakarta, Indonesia

Electrical Engineering

Afif Zuhri Arfianto, Program Studi Teknik Otomasi, Jurusan Kelistrikan Kapal, Politeknik Perkapalan Negeri Surabaya

Electrical Engineering

Elsayed T.Helmy, National Institute of oceanography and fisheries, Alexandria, Egypt

Electrical Engineering

Farhad Waseel, Department of mathematics, Kabul University, Kabul, Afghanistan

Electrical Engineering

References

H. Huang, N. Baddour, and M. Liang, “A method for tachometer-free and resampling-free bearing fault diagnostics under time-varying speed conditions,” Meas. J. Int. Meas. Confed., vol. 134, pp. 101–117, 2019.

Y. Wang, G. Xu, A. Luo, L. Liang, and K. Jiang, “An online tacholess order tracking technique based on generalized demodulation for rolling bearing fault detection,” J. Sound Vib., vol. 367, pp. 233–249, 2016.

J. Wu, Y. Zi, J. Chen, and Z. Zhou, “A modified tacho-less order tracking method for the surveillance and diagnosis of machine under sharp speed variation,” Mech. Mach. Theory, vol. 128, no. 28, pp. 508–527, 2018.

M. L. Ruiz Barrios, F. E. Hernández Montero, J. C. Gómez Mancilla, and E. Palomino Marín, “Tacho-less automatic rotational speed estimation (TARSE) for a mechanical system with gear pair under non-stationary conditions,” Meas. J. Int. Meas. Confed., vol. 145, pp. 480–494, 2019.

J. Wu, Y. Zi, J. Chen, and Z. Zhou, “Fault diagnosis in speed variation conditions via improved tacholess order tracking technique,” Meas. J. Int. Meas. Confed., vol. 137, pp. 604–616, 2019.

Z. Cheng, M. Gao, X. Liang, and L. Liu, “Incipient fault detection for the planetary gearbox in rotorcraft based on a statistical metric of the analog tachometer signal,” Measurement, vol. 151, p. 107069, 2019.

D. Siegel, H. Al-Atat, V. Shauche, L. Liao, J. Snyder, and J. Lee, “Novel method for rolling element bearing health assessment - A tachometer-less synchronously averaged envelope feature extraction technique,” Mech. Syst. Signal Process., vol. 29, pp. 362–376, 2012.

V. Sharma and A. Parey, “Frequency domain averaging based experimental evaluation of gear fault without tachometer for fluctuating speed conditions,” Mech. Syst. Signal Process., vol. 85, pp. 278–295, 2017.

S. Schmidt, P. S. Heyns, and J. P. de Villiers, “A tacholess order tracking methodology based on a probabilistic approach to incorporate angular acceleration information into the maxima tracking process,” Mech. Syst. Signal Process., vol. 100, pp. 630–646, 2018.

P. Kuo Weng and J. S. Shie, “A revolving retro-reflective marker for an optical tachometer,” Sensors Actuators A. Phys., vol. 24, no. 3, pp. 203–207, 1990.

C. Kuo, M. Fanton, L. Wu, and D. Camarillo, “Spinal constraint modulates head instantaneous center of rotation and dictates head angular motion,” J. Biomech., vol. 76, pp. 220–228, 2018.

H. Chen, M. C. Schall, and N. Fethke, “Accuracy of angular displacements and velocities from inertial-based inclinometers,” Appl. Ergon., vol. 67, pp. 151–161, 2018.

Q. Hu, J. Zhang, and Y. Zhang, “Velocity-free attitude coordinated tracking control for spacecraft formation flying,” ISA Trans., vol. 73, pp. 54–65, 2018.

E. Allseits, V. Agrawal, J. Lučarević, R. Gailey, I. Gaunaurd, and C. Bennett, “A practical step length algorithm using lower limb angular velocities,” J. Biomech., vol. 66, pp. 137–144, 2018.

Z. Hou, Y. Geng, B. Wu, and S. Huang, “Spacecraft angular velocity trajectory planning for SGCMG singularity avoidance,” Acta Astronaut., vol. 151, no. May, pp. 284–295, 2018.

T. Ito et al., “Active use of solar radiation pressure for angular momentum control of the PROCYON micro-spacecraft,” Acta Astronaut., vol. 152, no. August 2017, pp. 299–309, 2018.

R. Losero, J. Lauber, and T. M. Guerra, “Virtual strain gauge based on a fuzzy discrete angular domain observer: Application to engine and clutch torque estimation issues,” Fuzzy Sets Syst., vol. 343, pp. 76–96, 2018.

Z. Yang, J. Huo, and X. Han, “Angular-rate sensing by mode splitting in a Whispering-gallery-mode optical microresonator,” Meas. J. Int. Meas. Confed., vol. 125, no. July 2017, pp. 78–83, 2018.

X. Liu, S. Wang, T. Zhang, R. Huang, and Q. Wang, “A zero-velocity detection method with transformation on generalized likelihood ratio statistical curve,” Meas. J. Int. Meas. Confed., vol. 127, no. March, pp. 463–471, 2018.

A. F. Chávez-Gonzalez, P. Martínez-Ortiz, J. A. Pérez-Benítez, J. H. Espina-Hernández, and F. Caleyo, “Comparison of angular dependence of magnetic Barkhausen noise of hysteresis and initial magnetization curve in API5L steel,” J. Magn. Magn. Mater., vol. 446, pp. 18–27, 2018.

M. Patel, “Spiking and Excitatory/Inhibitory Input Dynamics of Barrel Cells in Response to Whisker Deflections of Varying Velocity and Angular Direction,” Neuroscience, vol. 369, pp. 15–28, 2018.

H. Alrowais et al., “Bio-inspired fluidic thermal angular accelerometer with inherent linear acceleration rejection,” Sensors Actuators, A Phys., vol. 279, pp. 566–576, 2018.

C. C. Lin and F. L. Yang, “A new image processing algorithm for three-dimensional angular velocity measurement and its application in a granular avalanche,” Adv. Powder Technol., vol. 29, no. 3, pp. 506–517, 2018.

L. Iafolla, L. Witthauer, A. Zam, G. Rauter, and P. C. Cattin, “Proof of principle of a novel angular sensor concept for tracking systems,” Sensors Actuators, A Phys., vol. 280, pp. 390–398, 2018.

B. F. Mentiplay, M. Banky, R. A. Clark, M. B. Kahn, and G. Williams, “Lower limb angular velocity during walking at various speeds,” Gait Posture, vol. 65, no. March, pp. 190–196, 2018.

Q. ZHU, G. MA, X. WANG, and A. WU, “Attitude control without angular velocity measurement for flexible satellites,” Chinese J. Aeronaut., vol. 31, no. 6, pp. 1345–1351, 2018.

A. C. Y. Yuen et al., “Numerical study of the development and angular speed of a small-scale fire whirl,” J. Comput. Sci., vol. 27, pp. 21–34, 2018.

H. H. Lee, J. I. Yoon, and H. S. Kim, “Single-roll angular-rolling: A new continuous severe plastic deformation process for metal sheets,” Scr. Mater., vol. 146, pp. 204–207, 2018.

M. J. F. Digonnet and M. J. Grant, “Comments on ‘Simultaneous measurement of angular velocities of two vertical directions in a slow-light structure,’” Opt. Fiber Technol., vol. 45, no. December 2017, pp. 250–254, 2018.

H. Gui and G. Vukovich, “Distributed almost global finite-time attitude consensus of multiple spacecraft without velocity measurements,” Aerosp. Sci. Technol., vol. 75, pp. 284–296, 2018.

Downloads

Published

2020-02-26

Issue

Vol. 1 No. 3 (2020): May

Section

Articles

License

Authors who publish with this journal agree to the following terms: 

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

 

This journal is based on the work at https://journal.umy.ac.id/index.php/jrc under license from Creative Commons Attribution-ShareAlike 4.0 International License. You are free to:

  1. Share – copy and redistribute the material in any medium or format.
  2. Adapt – remix, transform, and build upon the material for any purpose, even comercially.

The licensor cannot revoke these freedoms as long as you follow the license terms, which include the following:

  1. Attribution. You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
  2. ShareAlike. If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.
  3. No additional restrictions. You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.

 

• Creative Commons Attribution-ShareAlike (CC BY-SA)

Creative Commons License
JRC is licensed under an International License