Arduino-based Mini Shaker for Automatic Chemical Solution Mixer

Authors

  • Nur Hudha Wijaya Universitas Muhammadiyah Yogyakarta
  • Dian Friska Novela Department of Electrical Engineering, Universitas Muhammadiyah Yogyakarta, Yogyakarta, Indonesia
  • Nishith Shahu Departement of Electrical Engineering, Gujarat Technological University, India
  • Mian Usman Sattar Information Systems, University of Management and Technology, Pakistan.

DOI:

https://doi.org/10.18196/jrc.1641

Keywords:

chemical solution, mixer, Arduino

Abstract

The purpose of the research was to make an Arduino-based mini shaker for automatic mixing of chemical solutions. The use of the tool was expected to save time and energy in the process of mixing chemical solutions, facilitate laboratory workers in mixing the chemical solutions quickly and efficiently, and for a safety reason in the laboratory. The design of this tool consists of a time sensor, speed sensor, microcontroller, motor driver and Dc motor. This tool can regulate the speed of a DC motor with three speeds namely 100 RPM low, 150 normal RPM, and 180 high RPM. Based on the results of motor speed measurements, the average error at the motor speed is low 1.4%, normal 2.5%, and high 2.54%, and the average error at the timer is 1 minute 0.03%, 2 minutes 0,1%, 3 minutes 0.05%, 4 minutes 0.016%, and 5 minutes 0.03%.

Author Biographies

Dian Friska Novela, Department of Electrical Engineering, Universitas Muhammadiyah Yogyakarta, Yogyakarta, Indonesia

Electrical Engineering

Nishith Shahu, Departement of Electrical Engineering, Gujarat Technological University, India

Electrical Engineering

Mian Usman Sattar, Information Systems, University of Management and Technology, Pakistan.

Information Systems

References

H. S. Khan and M. B. Kadri, “DC motor speed control by embedded PI controller with hardware-in-loop simulation,” in 2013 3rd IEEE International Conference on Computer, Control and Communication (IC4), 2013, pp. 1–4.

Jia Yunfei, Liu Jiping, and Jiang Feng, “Design of DC motor wireless controller based on MCU MSP430,” in Proceedings 2013 International Conference on Mechatronic Sciences, Electric Engineering and Computer (MEC), 2013, pp. 3492–3495.

G. Rajeshkanna, “Modern speed control of separately excited DC Motor by Boost converter fed field control method,” in 2013 International Conference on Computer Communication and Informatics, 2013, pp. 1–7.

C. S. Gohiya, S. S. Sadistap, S. A. Akbar, and B. A. Botre, “Design and development of digital PID controller for DC motor drive system using embedded platform for mobile robot,” in 2013 3rd IEEE International Advance Computing Conference (IACC), 2013, pp. 52–55.

M. A. J. Paul, “Design and performance analysis of automated two axis solar tracking system for steam generation,” in 2013 International Conference on Energy Efficient Technologies for Sustainability, 2013, pp. 432–437.

I. G. A. P. R. Agung, S. Huda, and I. W. A. Wijaya, “Speed control for DC motor with pulse width modulation (PWM) method using infrared remote control based on ATmega16 microcontroller,” in 2014 International Conference on Smart Green Technology in Electrical and Information Systems (ICSGTEIS), 2014, no. November, pp. 108–112.

P. Kaur and S. Chatterji, “A novel framework based on AVR microcontroller for automated testing and analysis of DC motors,” in 2014 Recent Advances in Engineering and Computational Sciences (RAECS), 2014, pp. 1–6.

M. Ashmi, S. Jayaraj, and K. S. Sivanandan, “Development of a robust microcontroller based output feedback control for assistive limb,” in 2014 IEEE Conference on Biomedical Engineering and Sciences (IECBES), 2014, no. December 2014, pp. 193–197.

B. B. V. Kanth, G. S. Pavankumar, S. Arunkumar, and M. Venkatesan, “Design of motor speed control using LabVIEW for air-flow control in wind tunnels,” in 2014 IEEE International Conference on Computational Intelligence and Computing Research, 2014, pp. 1–4.

T. Araari, I. Jaziri, L. Charaabi, and K. Jelassi, “DC motor control based on embedded Linux,” in 2014 International Conference on Electrical Sciences and Technologies in Maghreb (CISTEM), 2014, pp. 1–6.

T. M. Sai and S. K. Kumar, “Speed control of DC motor using voice commands,” in 2016 International Conference on Computation of Power, Energy Information and Commuincation (ICCPEIC), 2016, pp. 800–803.

K. R. Asha, P. S. Tasleem, A. V. Ravi Kumar, S. M. Swamy, and K. R. Rekha, “Real Time Speed Control of a DC Motor by Temperature Variation Using LabVIEW and Arduino,” in 2017 International Conference on Recent Advances in Electronics and Communication Technology (ICRAECT), 2017, pp. 72–75.

S. D. Sahputro, F. Fadilah, N. A. Wicaksono, and F. Yusivar, “Design and implementation of adaptive PID controller for speed control of DC motor,” in 2017 15th International Conference on Quality in Research (QiR) : International Symposium on Electrical and Computer Engineering, 2017, vol. 2017-Decem, no. 1, pp. 179–183.

S. N. Thanh, K. N. Thanh, C. N. The, P. P. Hung, and H. H. Xuan, “Development of fuzzy logic controller for DC motor using personal computer and inexpensive microcontroller,” in 2014 13th International Conference on Control Automation Robotics & Vision (ICARCV), 2014, vol. 2014, no. December, pp. 1310–1314.

V.-V. Ciucur, “Speed position control system for DC motor,” in 2014 16th International Conference on Harmonics and Quality of Power (ICHQP), 2014, pp. 876–879.

S. Jayaprakash and V. Ramakrishnan, “Analysis of solar based closed loop DC-DC converter using PID and fuzzy logic control for separately excited motor drive,” in 2014 IEEE National Conference on Emerging Trends In New & Renewable Energy Sources And Energy Management (NCET NRES EM), 2014, pp. 118–122.

M. Arici and A. O. Arslan, “Self-tuning speed control of permanent magnet DC motor,” in 2015 9th International Conference on Electrical and Electronics Engineering (ELECO), 2015, no. 4, pp. 1113–1116.

A. Bara, S. Dale, C. Rusu, and H. Silaghi, “DC electrical drive control with fuzzy systems,” in 2015 13th International Conference on Engineering of Modern Electric Systems (EMES), 2015, vol. 1, no. 1, pp. 1–4.

S. Angalaeswari, A. Kumar, D. Kumar, and S. Bhadoriya, “Speed control of permanent magnet (PM)DC motor using Arduino and LabVIEW,” in 2016 IEEE International Conference on Computational Intelligence and Computing Research (ICCIC), 2016, pp. 1–6.

I. Jaziri, L. Charaabi, and K. Jelassi, “A closed Loop DC Motor Control using low cost single-board microcontroller based on embedded Linux,” in 2016 International Conference on Electrical Sciences and Technologies in Maghreb (CISTEM), 2016, pp. 1–5.

U. Sarma and P. . Bordoloi, “Speed Control of A DC Motor Using PLC and PIC Microcontroller,” in 2017 14th IEEE India Council International Conference (INDICON), 2017, pp. 1–6.

N. M. A. Mohamed, A. A. A. Abdalaziz, A. A. A. Ahmed, and A. A. A. Ahmed, “Implementation of a PID control system on microcontroller (DC motor case study),” in 2017 International Conference on Communication, Control, Computing and Electronics Engineering (ICCCCEE), 2017, no. 1, pp. 1–5.

M. Rad, F. Simonca, A. Fratean, and P. Dobra, “Embedded speed control of BLDC motors using LPC1549 microcontroller,” in 2016 IEEE International Conference on Automation, Quality and Testing, Robotics (AQTR), 2016, pp. 1–5.

F. E. V. Taveiros, L. S. Barros, and C. M. V. Barros, “Conventional and adaptive strategies applied to DC motor control using microcontroller PIC18F4520,” in 2018 Simposio Brasileiro de Sistemas Eletricos (SBSE), 2018, no. 4, pp. 1–6.

P. Surana, Sreejith R., and K. R. Rajagopal, “A low cost position sensorless brushless DC motor drive,” in 2016 IEEE International Conference on Power Electronics, Drives and Energy Systems (PEDES), 2016, vol. 2016-Janua, pp. 1–5.

C. D. Britto and P. Kumar, “Analysis of Boost converter fed DC motor,” in 2016 International Conference on Computation of Power, Energy Information and Commuincation (ICCPEIC), 2016, pp. 487–489.

L. Lindner et al., “Issues of exact laser ray positioning using DC motors for vision-based target detection,” in 2016 IEEE 25th International Symposium on Industrial Electronics (ISIE), 2016, vol. 2016-Novem, pp. 929–934.

S. Bilgaiyan, S. James, S. S. Bhonsle, S. Shahdeo, and Keshavamurthy, “Android based signboard detection using image and voice alert system,” in 2016 IEEE International Conference on Recent Trends in Electronics, Information & Communication Technology (RTEICT), 2016, pp. 1488–1491.

A. Kumar, H. Saraf, and R. Kumar, “Hardware design of closed loop four quadrant dc motor drive with regenerative braking,” in 2018 2nd International Conference on Inventive Systems and Control (ICISC), 2018, pp. 287–292.

C.-T. Chu, Y.-K. Wang, and H.-L. Liang, “SISO PID-fuzzy controller for BLDC motor speed control base on low cost MSP430 solution,” in 2016 5th International Symposium on Next-Generation Electronics (ISNE), 2016, pp. 1–2.

Downloads

Published

2020-06-30

Issue

Vol. 1 No. 6 (2020): November

Section

Articles

License

Authors who publish with this journal agree to the following terms: 

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

 

This journal is based on the work at https://journal.umy.ac.id/index.php/jrc under license from Creative Commons Attribution-ShareAlike 4.0 International License. You are free to:

  1. Share – copy and redistribute the material in any medium or format.
  2. Adapt – remix, transform, and build upon the material for any purpose, even comercially.

The licensor cannot revoke these freedoms as long as you follow the license terms, which include the following:

  1. Attribution. You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
  2. ShareAlike. If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.
  3. No additional restrictions. You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.

 

• Creative Commons Attribution-ShareAlike (CC BY-SA)

Creative Commons License
JRC is licensed under an International License