Simulation Model of PID Controller for DC Servo Motor at Variable and Constant Speed by Using MATLAB

Zainab B. Abdullah, Salam Waley Shneen, Hashmia S. Dakheel

Abstract


The current simulation is conducted in order to develop an appropriate design for the control systems and control the speed of the electric motor. To obtain the appropriate and required design, work is carried out for two cases, a constant speed and the other case at variable speed in different conditions for operation of dc servo motor, these conditions include rotating in a clockwise direction, break and returns rotating in the opposite clockwise direction. Through the proposed working conditions, it is possible to obtain the best values for the parameters of the control unit that improve the working performance of dc servo motor, which were shown by the simulation results and their values were kp =5, ki=3 and kd=5 for PID controller. Which changed the system response speed, rise time and the upper and lower bypass ratio at acceptable rates and ratios to prove an improvement procedure in the work of the electric motor.

Keywords


DCSM; PID Controller; Speed; Position

Full Text:

PDF

References


H. S. Dakheel, Z. B. Abdullah, N. S. Jasim, and S. W. Shneen, "Simulation model of ANN and PID controller for direct current servo motor by using Matlab/Simulink," TELKOMNIKA Telecommunication Computing Electronics and Control, vol. 20, no. 4, pp. 922-932, 2022.

N. M. Zakaria and A. O. Elnady, "Implementation of Position Control Servo DC Motor with PID Controller to Humanoid Robot Arm," 5 th IUGRC International Undergraduate Research Conference, Military Technical College, Cairo, Egypt, Aug 9th – Aug 12st, 2021.

J. Priya, A. Jeevanandham, K. Rajalashmi, "Fuzzy Logic Controller for Position Control of Servo Motor," International Journal of Innovative Technology and Exploring Engineering (IJITEE), vol. 8, no. 3, pp. 99-102, 2019.

A. A. Hassen, "Real Time Digital Speed Control System for DC Servo Motor Using LabVIEW 8.5 Package," Engineering and Technology Journal, vol. 28, no. 6, 2010.

S. W. Shneen, M. Q. Sulttan, and M. H. Jaber, "Variable speed control for 2Ph-HSM in RGS: a comparative simulation study," International Journal of Electrical and Computer Engineering, vol. 10, no. 3, p. 2285, 2020.‏

E. H. Abdelhameed, T. H. Mohamed and G. El-saady, "Design of Hybrid Fuzzy and Position-Velocity Controller for Precise Positioning of a Servo System," International Journal of Applied Energy Systems, vol. 2, no. 2, pp. 111-115, 2020.

R. Manikandan and R. Arulmozhiyal, "Position Control of DC Servo Drive Using Fuzzy Logic Controller," 2014 International Conference on Advances in Electrical Engineering (ICAEE), pp. 1-5, 2014.

M, H. Jasim, "Tuning of a PID controller by bacterial foraging algorithm for position control of DC servo motor," Engineering and Technology Journal, vol. 36, no. 3A, pp. 287-294, 2018.‏

S. W. Shneen, H. S. Dakheel, and Z. B. Abdulla, "Design and implementation of variable and constant load for induction motor," International Journal of Power Electronics and Drive Systems, vol. 11, no. 2, p. 762, 2020.‏

T. T. Lynn and Eaint, "Position Control of DC Servo Drive by Fuzzy Logic Controller in Flat-Bed Screen Printing Machine," American Scientific Research Journal for Engineering, Technology, and Sciences (ASRJETS), vol. 26, no 1, pp 8-19, 2016.

F. N. Abdullah, G. A. Aziz, S. W. Shneen, "Simulation Model of Servo Motor by Using Matlab," Journal of Robotics and Control (JRC), vol. 3, no. 2, pp. 176-179, 2022.

H. Alzarok, H. M. Aiyoub, "Tuning of a Speed Control System for DC Servo Motor Using Genetic Algorithm," The International Journal of Engineering and Information Technology (IJEIT), vol. 6, no. 2, pp. 141-150, 2020.

L. S. Mezher, "Characteristics of Servo DC Motor with PID Controller," Journal of Mechanical Engineering Research and Developments, vol. 44, no 2, pp 392-400, 2021.

L. S. Mezher, "Speed control for servo DC motor with different tuning PID controller with," Journal of Mechanical Engineering Research and Developments, vol. 44, no. 1, pp. 294-303, 2021.

A.-A. S. A. -Salam, "Comparison between FLC and PID Controller for Speed Control of DC Motor," International Robotics & Automation Journal, vol. 8, no. 2, pp. 40-45, 2022.

A. M. Abba, T. Karataev, S. Thomas and A. M. Ali, "Optimal PID Controller Tuning for DC Motor Speed Control Using Smell Agent Optimization Algorithm," FUOYE Journal of Engineering and Technology, vol. 7, no. 1, pp.23-27, 2022.

M. A. Baballe, et al., "A Look at the Different Types of Servo Motors and Their Applications," Global Journal of Research in Engineering & Computer Sciences, vol. 2, no. 3, pp. 1-6, 2022.

V. Balgur, A. Gonzalez, P. Garcia, and F. Blanes, "Enhanced 2-DOF PID Controller Tuning Based on an Uncertainty and Disturbance Estimator with Experimental Validation," IEEE Access, vol. 9, pp. 99092-99102, 2021.

H. S. Dakheel, Z. B. Abdulla, H. J. Jawad, A. J. Mohammed, " Comparative analysis of PID and neural network controllers for improving starting torque of wound rotor induction motor," TELKOMNIKA Telecommunication, Computing, Electronics and Control, vol. 18, no. 6, pp. 3142-3154, 2020.

S. T. Kurdi, and N. M. Ameen, "DC Servo Position Control Parameter Estimation," Engineering and Technology Journal, vol. 28, no. 5, 2010.‏

S. W. Shneen, "Advanced optimal for power-electronic systems for the grid integration of energy sources," Indonesian Journal of Electrical Engineering and Computer Science, vol. 1, no. 3, pp. 543-555, pp. 2016.

S. Memon and A. N. Kalhoro, "Design of Multivariable PID Controllers: A Comparative Study," IJCSNS International Journal of Computer Science and Network Security, vol. 21, no. 8, pp. 212-218, 2021.

M. Ahmed, N. M. Tahir, A. Y. Zimit, M. Idi, K. A. Abubakar, and S. A. Jalo, "Improved PID Controller for DC Motor Control Improved PID Controller for DC Motor Control," IOP Conference Series Materials Science and Engineering, vol. 1052, no. 1, p. 12058, 2021.

S. W. Shneen, "Advanced optimal for three phase rectifier in power-electronic systems," Indonesian Journal of Electrical Engineering and Computer Science, vol. 11, no. 3, pp. 821-830, 2018.‏

S. W. Shneen, D. H. Shaker, F. N. Abdullah, "Simulation model of single phase PWM inverter by using MATLAB/Simulink," International Journal of Electrical and Computer Engineering (IJECE), vol. 11, no. 5, pp. 3791-3797, 2021.

W. Cai, et al., "Review and development of electric motor systems and electric powertrains for new energy vehicles," Automotive Innovation, vol. 4, no. 1, pp. 3-22, 2021.‏

S. W. Shneen, “Advanced optimal for three phase rectifier in power-electronic systems," Indonesian Journal of Electrical Engineering and Computer Science, vol. 11, no. 3, pp. 821-830, 2018.

H. Hayashi, et al., "Efficiency improvements of switched reluctance motors with high-quality iron steel and enhanced conductor slot fill," IEEE Transactions on Energy Conversion, vol. 24, no. 4, pp. 819-825, 2009.‏

F. W. Lewis, S. Jagannathan, and A. Yesildirak, “Neural network control of robot manipulators and non-linear systems,” CRC press, 1998.‏

S. W. Shneen, et al, "Application of LFAC {16 2/3Hz} for electrical power transmission system: a comparative simulation study," TELKOMNIKA (Telecommunication Computing Electronics and Control), vol. 17, no. 2, pp. 1055-1064, 2019.‏

T. K. Nizami, et al., "Enhanced dynamic performance in DC–DC converter‐PMDC motor combination through an intelligent non‐linear adaptive control scheme," IET Power Electronics, vol. 15, no. 15, pp. 1607-1616, 2022.‏

D. Somwanshi, M. Bundele, G. Kumar, G. Parashar, "Comparison of Fuzzy-PID and PID Controller for Speed Control of DC Motor using LabVIEW," Procedia Computer Science, vol. 152, pp. 252–260, 2019.

S. W. Shneen, and G. A. Aziz, "Simulation model of 3-phase PWM rectifier by using MATLAB/Simulink," International Journal of Electrical and Computer Engineering, vol. 11, no. 5, p. 3736, 2021.‏

M. A. Akbar, "Simulation of Fuzzy Logic Control for DC Servo Motor using Arduino based on Matlab/Simulink," International Conference of Intelligent Autonomous Agents, Network & System, pp.42-46, 2014.

M. Akar and I. Temiz, "Motion controller design for the speed control of dc servo motor," International Journal of Applied Mathematics and Informatics, vol. 1, no. 4, pp. 131-137, 2007.

D. K. Meena and S. Chahar, "Speed Control of DC Servo using Genetic Algorithm," IEEE Conference on Information, Communication, Instrumentation and Control (ICICIC), pp. 1-7, 2017.

S. W. Shneen, "Advanced Optimal for PV system coupled with PMSM," Indonesian Journal of Electrical Engineering and Computer Science, vol. 1, no. 3, pp. 556-565, 2016.‏

R. Kristiyono and W. Wiyono, "Autotuning Fuzzy PID Controller for Speed Control of BLDC Motor," Journal of Robotics and Control (JRC), vol. 2, no. 5, pp. 400-407, 2021.

A. M. Alsayed, E. K. Elsayed, "Optimize Position Control of DC Servo Motor using PID ‎Controller Tuning with Krill Herd algorithm," International Journal of Engineering and Information Systems (IJEAIS), vol. 4, no. 12, pp. 141-147, 2020.

S. W. Shneen, C. Mao, and D. Wang, "Advanced optimal PSO, Fuzzy and PI controller with PMSM and WTGS at 5Hz side of generation and 50Hz Side of Grid," International Journal of Power Electronics and Drive Systems, vol. 7, no. 1, p. 173, 2016.‏

G. Vasudevarao, V. Rangavalli, "Comparison of Speed Control of Dc Servo Motor using Pi, PID, Fuzzy, SMC," International Advanced Research Journal in Science, Engineering and Technology, vol. 3, no. 11, pp. 151-156, 2016.

C. Bharatiraja, et al., "Low cost real time centralized speed control of DC motor using lab view-NI USB 6008," International Journal of Power Electronics and Drive Systems, vol. 7, no. 3, p. 656, 2016.

K. J. Åström, H. Elmqvist, and S. E. Mattsson, "Evolution of continuous-time modeling and simulation," Esm, pp. 9-18, 1998.‏

S. W. Shneen, D. H. Shaker, and F. N. Abdullah, "Simulation model of PID for DC-DC converter by using MATLAB," International Journal of Electrical and Computer Engineering, vol. 11, no. 5, p. 3791, 2021.

S. Ayasun, and C. O. Nwankpa, "Induction motor tests using MATLAB/Simulink and their integration into undergraduate electric machinery courses," IEEE Transactions on education, vol. 48, no. 1, pp. 37-46, 2005.‏

A. Banik, et al., "Design, modelling, and analysis of novel solar PV system using MATLAB," Materials today: proceedings, vol. 51, pp. 756-763, 2022.

R. Newby, et al., "Geste antagoniste effects on motor performance in dystonia—a kinematic study," Movement Disorders Clinical Practice, vol. 9, no. 6, pp. 759-764, 2022.‏

P. F. Le Roux, and M. K. Ngwenyama, "Static and Dynamic Simulation of an Induction Motor Using Matlab/Simulink," Energies, vol. 15, no. 10, p. 3564, 2022.

H. Maghfiroh, A. Ramelan, and F. Adriyanto, "Fuzzy-PID in BLDC Motor Speed Control Using MATLAB/Simulink," Journal of Robotics and Control (JRC), vol. 3, no. 1, pp. 8-13, 2022.‏

R. Subasri, et al., "Comparison of BPN, RBFN and wavelet neural network in induction motor modelling for speed estimation," International Journal of Ambient Energy, vol. 43, no. 1, pp. 3246-3251, 2022.‏

N. Rosjat, and S. Daun, "DST (Dynamic Synchronization Toolbox): A MATLAB Implementation of the Dynamic Phase-Locking Pipeline from Stimulus Transformation into Motor Action: Dynamic Graph Analysis Reveals a Posterior-to-Anterior Shift in Brain Network Communication of Older Subjects," Journal of Open Research Software, vol. 10, no. 1, 2022.‏

A. B. Martínez, et al., "MATLAB/Simulink modeling of electric motors operating with harmonics and unbalance," International Journal of Electrical and Computer Engineering (IJECE), vol. 12, no. 5, pp. 4640-4648, 2020.

S. Ghosh, "MATLAB Simulation of Circle Diagram in Three Phase Induction Motor," IETE Journal of Education, vol. 63, no. 2, pp. 63-67, 2022.

M. K. Oudah, M. Q. Sulttan, and S. W. Shneen, "Fuzzy type 1 PID controllers design for TCP/AQM wireless networks," Indonesian Journal of Electrical Engineering and Computer Science, vol. 21, no. 1, pp. 118-127, 2021.‏




DOI: https://doi.org/10.18196/jrc.v4i1.15866

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 Zainab B. Abdullah, salam waley shneen, Hashmia S. Dakheel

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

 

Journal of Robotics and Control (JRC)

P-ISSN: 2715-5056 || E-ISSN: 2715-5072
Organized by Peneliti Teknologi Teknik Indonesia
Published by Universitas Muhammadiyah Yogyakarta in collaboration with Peneliti Teknologi Teknik Indonesia, Indonesia and the Department of Electrical Engineering
Website: http://journal.umy.ac.id/index.php/jrc
Email: jrcofumy@gmail.com

Kuliah Teknik Elektro Terbaik