Design and Implementation of No Load, Constant and Variable Load for DC Servo Motor

Salam Waley Shneen, Hashmia S Dakheel, Zainab B Abdullah

Abstract


Simulations were conducted to improve and design an appropriate control system and obtain a model with the required development to suit the operation of the engine with constant and variable loads, which are the proposed working conditions that are suitable for many applications. The current simulation aims to build and design a model for an electric motor (DC Servo motor) and a model for a conventional controller (PID). The proposed model addresses the cases of fixed and variable loads in terms of using the controller that improves the performance of the motor’s work for different conditions. Three cases were developed to conduct the proposed tests, which included the case of no-load, fixed and variable load. Tests were conducted. Without the console and for the purpose of comparison and observation of improvement, the test was conducted with the addition of the console. The results showed system performance may improve depending on usage using traditional control systems. Performance measurement criteria are adopted for the purpose of comparison and observation of performance improvement. The criteria that are adopted are rise time and stability (steady state) in addition to the ratio of the rate of under and over-shoot. Where it can be deduced from this the possibility of using different control systems, including traditional ones, to improve performance, and they include controlling the speed of the motors, as well as controlling the effort, and the consequent effects on the subject of the study, as it deals with transient cases and changing operating conditions with more than acceptable efficiency and relatively high quality. There are four state simulation include, 1st at no load without controller: rise time equal  309.886ms , overshoot equal  44.203% and undershoot equal 9.597%.2nd  at load without controller: rise time equal  216.319ms , overshoot equal  58.654% and undershoot equal 0.210%.3rd  at no load with PID controller: rise time equal  1.177s , overshoot equal  0.505% and undershoot equal 1.914%.4th   at load with PID controller: rise time equal  1.112s , overshoot equal  0.509% and undershoot equal 5.856%.

Keywords


DC Servo Motor; PID Controller; No-load; Constant Load; Variable Load.

Full Text:

PDF

References


T. Lakkoju, “Speed control of DC servomotor using Chopper based PI Controller,” International Journal of Progressive Research in Science and Engineering, vol. 2, no. 1, pp.5-10, 2021.

A. M. Alsayed, E. K. Elsayed, “Optimize Position Control of DC Servo Motor using PID ‎Controller Tuning with Krill Herd Algorithm,” International Journal of Engineering and Information Systems (IJEAIS), vol. 4, no. 12, pp. 141-147, 2020.

H. S. Dakheel, Z. B. Abdullah, N. S. Jasim, S. W. Shneen, “Simulation model of ANN and PID controller for direct current servo motor by using Matlab/Simulink,” TELKOMNIKA Telecommunication Computing Electronics and Control, vol. 20, no. 4, pp. 922-932, 2022.

J. M. Kiss, P. T. Szemes, and P. Aradi, “Sliding mode control of a servo system in LabVIEW: Comparing different control methods,” International Review of Applied Sciences and Engineering, vol. 12, no. 2, pp. 201-210, 2021.

Z. Yin, L. Gong, C. Du, J. Liu, and Y. Zhong, “Sliding Mode Control for Servo Motors Based on the Differential Evolution Algorithm,” Journal of Power Electronics, vol. 18, no. 1, pp. 92-102, 2018.

S. W. Shneen and G. A. Aziz, “Simulation model of 3-phase PWM rectifier by using MATLAB/Simulink,” International Journal of Electrical and Computer Engineering, vol. 11, no. 5, p. 3736, 2021.

S. Harshitha, S. Shamanth, and A. K. Chari, “A Review of Various Controller Techniques Designed for the Operational Control of DC and Servo Motors,” Journal of Physics: Conference Series, vol. 2273, no. 1, p. 012001, 2022.

A. Batool, N. Ain, A. A. Amin, M. Adnan, and M. H. Shahbaz, “A comparative study of DC servo motor parameter estimation using various techniques,” Journal for Control, Measurement, Electronics, Computing and Communications (AUTOMATIKA), vol. 63, no. 2, pp. 303-312, 2022.

Manal H. Jasim," Tuning of a PID Controller by Bacterial Foraging Algorithm for Position Control of DC Servo Motor", Engineering and Technology Journal Vol.36, PartA, No.3,2018, pp.287-294.

Fatin Nabeel Abdullah, Ghada Adel Aziz, Salam WaleyShneen," Simulation Model of Servo Motor by Using Matlab", Journal of Robotics and Control (JRC) Volume 3, Issue 2, March 2022 ISSN: 2715-5072,pp.176-179.

M. G. Rabie, S. Selim, M. A. Aziz, and M. A. Moharm, “Investigating the Dynamic response of Electrohydraulic Servo Motor,” Engineering Research Journal, vol. 43, no. 2, pp. 109-117, 2020.

L. S. Mezher, “Characteristics of Servo DC Motor with PID Controller,” Journal of Mechanical Engineering Research and Developments, vol. 44, no. 2, pp. 392-400, 2021.

S. W. Shneen, H. S. Dakheel, Z. B. Abdulla, “Design and implementation of variable and constant load for induction motor,” International Journal of Power Electronics and Drive System (IJPEDS), vol. 11, no. 2, pp.762-773, 2020.

H. Sun, X. Wang, Q. Lin, X. Wang, and S. Su, “The design of the DC servo motor controller based on fuzzy immune PID algorithm,” 2017 36th Chinese Control Conference (CCC), pp. 4724-4729, 2017, doi: 10.23919/ChiCC.2017.8028098.

A-. A. S. A-. Salam, “Comparison between FLC and PID Controller for Speed Control of DC Motor,” International Robotics & Automation Journal, vol. 8, no. 2, pp. 40-45, 2022.

C. Li, W. Yi, H. Yin, and J. Guan, “Fuzzy pid control of electromechanical actuator system,” In Journal of Physics: Conference Series, vol. 1721, no. 1, p. 012052, 2021.

J. Lee, P. H. Chang, B. Yu and M. Jin, “An Adaptive PID Control for Robot Manipulators Under Substantial Payload Variations,” in IEEE Access, vol. 8, pp. 162261-162270, 2020, doi: 10.1109/ACCESS.2020.3014348.

L. S. Mezher, “Speed Control for Servo DC Motor with Different Tuning PID Controller with Labview,” Journal of Mechanical Engineering Research and Developments, vol. 44, no. 1, pp. 294-303, 2021.

S. W. Shneen, “Advanced Optimal for PV system coupled with PMSM,” Indonesian Journal of Electrical Engineering and Computer Science, vol. 1, no. 3, pp. 556-565, 2016.‏

M. A. Baballe, M. I. Bello, A. A. Umar, A. K. Shehu, D. Bello, F. T. Abdullahi, “Different Types of Servo Motors and Their Applications,” 1st International Conference on Engineering and Applied Natural Sciences, pp. 974-979, 2022.

W. Aribowo, S. Supari, and B. Suprianto, “Optimization of PID parameters for controlling DC motor based on the aquila optimizer algorithm,” International Journal of Power Electronics and Drive Systems (IJPEDS), vol. 13, no. 1, pp. 2808-2814, 2022.

N. R. Setiawan, A. Ma'arif, and N. S. Widodo, “DC Motor Controller Using Full State Feedback,” Control Systems and Optimization Letter, vol. 1, no. 1, pp. 7-11, 2023.

S. W. Shneen, “Advanced optimal for power-electronic systems for the grid integration of energy sources,” Indonesian Journal of Electrical Engineering and Computer Science, vol. 1, no. 3, pp. 543-555, 2016.

A. Ma’arif, Iswanto, N. M. Raharja, P. A. Rosyady, A. R. C. Baswara, and A. A. Nuryono, “Control of DC Motor Using Proportional Integral Derivative (PID): Arduino Hardware Implementation,” 2020 2nd International Conference on Industrial Electrical and Electronics (ICIEE), pp. 74-78, 2020, doi: 10.1109/ICIEE49813.2020.9277258.‏

M. Zadehbagheri, A. Ma'arif, R. Ildarabadi, M. Ansarifard, and I. Suwarno, “Design of Multivariate PID Controller for Power Networks Using GEA and PSO,” Journal of Robotics and Control (JRC), vol. 4, no. 1, pp. 108-117, 2023.

M. D. I. Putri, A. Ma'arif, and R. D. Puriyanto, “Pengendali Kecepatan Sudut Motor DC Menggunakan Kontrol PID dan Tuning Ziegler Nichols,” Techno (Jurnal Fakultas Teknik, Universitas Muhammadiyah Purwokerto), vol. 23, no. 1, pp. 9-18, 2022.

A. J. Attiya, S. W. Shneen, B. A. Abbas, and Y. Wenyu, “Variable Speed Control Using Fuzzy-PID Controller for Two-phase Hybrid Stepping Motor in Robotic Grinding,” Indonesian Journal of Electrical Engineering and Computer Science, vol. 3, no. 1, pp. 102-118, 2016.

Q. Ariyansyah and A. Ma'arif, “DC Motor Speed Control with Proportional Integral Derivative (PID) Control on the Prototype of a Mini-Submarine,” Journal of Fuzzy Systems and Control, vol. 1, no. 1, pp. 1-7, 2023.

A. Ma'arif and N. R. Setiawan, “Control of DC motor using integral state feedback and comparison with PID: simulation and arduino implementation,” Journal of Robotics and Control (JRC), vol. 2, no. 5, pp. 456-461, 2021.

A. Ma’arif, H. Nabila, and O. Wahyunggoro, “Application of intelligent search algorithms in proportional-integral-derivative control of direct-current motor system,” Journal of Physics: Conference Series, vol. 1373, no. 1, 2019.‏

E. S. Rahayu, A. Ma’arif, and A. Çakan, “Particle swarm optimization (PSO) tuning of PID control on DC motor,” International Journal of Robotics and Control Systems, vol. 2, no. 2, pp. 435-447, 2022.

Y. Zahraoui, M. Akherraz, and A. Ma’arif, “A comparative study of nonlinear control schemes for induction motor operation improvement,” International Journal of Robotics and Control Systems, vol. 2, no. 1, pp. 1-17, 2022.

E. W. Suseno and A. Ma’arif, “Tuning of PID controller parameters with genetic algorithm method on DC motor,” International Journal of Robotics and Control Systems, vol. 1, no. 1, pp. 41-53, 2021.

R. Stanisławski, M. Rydel, and Z. Li, “A New Reduced-Order Implementation of Discrete-Time Fractional-Order PID Controller,” in IEEE Access, vol. 10, pp. 17417-17429, 2022, doi: 10.1109/ACCESS.2022.3150883.

D. H. Shaker, S. W. Shneen, F. N. Abdullah, and G. A. Aziz, “Simulation Model of Single-Phase AC-AC Converter by Using MATLAB,” Journal of Robotics and Control (JRC), vol. 3, no. 5, pp. 656-665, 2022.

S. W. Shneen, “Advanced optimal for three phase rectifier in power-electronic systems,” Indonesian Journal of Electrical Engineering and Computer Science, vol. 11, no. 3, pp. 821-830, 2018.

A. L. Shuraiji and S. W. Shneen, “Fuzzy Logic Control and PID Controller for Brushless Permanent Magnetic Direct Current Motor: A Comparative Study,” Journal of Robotics and Control (JRC), vol. 3, no. 6, pp. 762-768, 2022.

H. S. Dakheel, Z. B. Abdullah, and S. W. Shneen, “Advanced optimal GA-PID controller for BLDC motor,” Bulletin of Electrical Engineering and Informatics, vol. 12, no. 4, pp. 2077-2086, 2023.

A. M. Alsayed, E. K. Elsayed, “Optimize Position Control of DC Servo Motor using PID ‎Controller Tuning with Krill Herd algorithm,” International Journal of Engineering and Information Systems (IJEAIS), vol. 4, no. 12, pp. 141-147, 2020.

G. Vasudevarao and V. Rangavalli, “Comparison of Speed Control of DC Servo Motor using Pi, PID, Fuzzy, SMC,” International Advanced Research Journal in Science, Engineering and Technology, vol. 3, no. 11, pp. 151-156, 2016.

T. Lakkoju, “Speed control of DC servomotor using Chopper based PI Controller,” International Journal of Progressive Research in Science and Engineering, vol. 2, no. 1, pp. 5-10, 2021.

R. Bindu, M. K. Namboothiripad, “Tuning of PID Controller for DC Servo Motor using Genetic Algorithm,” International Journal of Emerging Technology and Advanced Engineering, vol. 2, no. 3, pp. 310-315, 2012.

S. W. Shneen, A. Z. Salman, Q. A. Jawad, and H. Shareef, “Advanced optimal by PSO-PI for DC motor,” Indonesian Journal of Electrical Engineering and Computer Scienc (IJEECS), vol. 16, no. 1, pp. 165-175, 2019, doi: 10.11591/ijeecs.v16.i1.pp165-175.

M. Nizam, H. Maghfiroh, B. Irfani, I. Inayati, and A. Ma’arif, “Designing and prototyping of lithium-ion charging system using multi-step constant current method,” World Electric Vehicle Journal, vol. 13, no. 10, p. 178, 2022.‏

A. Setiawan and A. Ma’arif, “Stirring system design for automatic coffee maker using OMRON PLC and PID control,” International Journal of Robotics and Control Systems, vol. 1, no. 3, pp. 390-401, 2021.‏

Z. B. Abdullah, S. W. Shneen, and H. S. Dakheel, “Simulation Model of PID Controller for DC Servo Motor at Variable and Constant Speed by Using MATLAB,” Journal of Robotics and Control (JRC), vol. 4, no. 1, pp. 54-59, 2023.

A. Ma'arif and A. Çakan, “Simulation and arduino hardware implementation of dc motor control using sliding mode controller,” Journal of Robotics and Control (JRC), vol. 2, no. 6, pp. 582-587, 2021.

S. W. Shneen, M. A. A. Hussein, J. A. Kadhum, and S. M. Ali, “Application of LFAC {16 2/3Hz} for electrical power transmission system: a comparative simulation study,” TELKOMNIKA (Telecommunication Computing Electronics and Control), vol. 17, no. 2, pp. 1055-1064, 2019.

D. Saputra, A. Ma'arif, H. Maghfiroh, P. Chotikunnan, and S. N. Rahmadhia, “Design and Application of PLC-based Speed Control for DC Motor Using PID with Identification System and MATLAB Tuner,” International Journal of Robotics and Control Systems, vol. 3, no. 2, pp. 233-244, 2023.

R. Rikwan and A. Ma'arif, “DC Motor Rotary Speed Control with Arduino UNO Based PID Control,” Control Systems and Optimization Letters, vol. 1, no. 1, pp. 27-31, 2023.

S. W. Shneen, D. H. Shaker, and F. N. Abdullah, “Simulation model of PID for DC-DC converter by using MATLAB,” International Journal of Electrical and Computer Engineering, vol. 11, no. 5, p. 3791, 2021.

S. W. Shneen, F. N. Abdullah, and D. H. Shaker, “Simulation model of single phase PWM inverter by using MATLAB/Simulink,” International Journal of Power Electronics and Drive Systems, vol. 12, no. 1, p. 212, 2021.




DOI: https://doi.org/10.18196/jrc.v4i3.17387

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 salam Waley shneen, Hashmia S. Dakheel, Zainab B. Abdullah

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

 

Journal of Robotics and Control (JRC)

P-ISSN: 2715-5056 || E-ISSN: 2715-5072
Organized by Peneliti Teknologi Teknik Indonesia
Published by Universitas Muhammadiyah Yogyakarta in collaboration with Peneliti Teknologi Teknik Indonesia, Indonesia and the Department of Electrical Engineering
Website: http://journal.umy.ac.id/index.php/jrc
Email: jrcofumy@gmail.com

Kuliah Teknik Elektro Terbaik