The Design of Tachometer Contact and Non-Contact Using Microcontroller

Tatiya Padang Tunggal, Lailicia Anggi Kirana, Afif Zuhri Arfianto, Elsayed T.Helmy, Farhad Waseel

Abstract


Calibration is required for various kinds of tools from kitchen tools such as stirrers or mixers to medical tools such as temperature calibration, ECG, blood pressure, and other instrumentation tools to be according to the required standards. In medical devices, a digital tachometer has been used as a calibration support device to measure the speed of objects that rotate in RPM on the centrifuge. Some medical devices are calibrated in km/hour, for example, the ergo cycle and treadmill. Two different devices or a conversion from RPM to km/hour are required. The research aimed to design a measurement device that performed calibration of devices with different units, namely tachometer that can be used to measure speed in RPM and km/hr. Based on the research objective, a tool was made to measure the motor's rotational speed using the E18-D80NK sensor, microcontroller, and LCD without touching the object being measured.

Full Text:

PDF

References


H. Huang, N. Baddour, and M. Liang, “A method for tachometer-free and resampling-free bearing fault diagnostics under time-varying speed conditions,” Meas. J. Int. Meas. Confed., vol. 134, pp. 101–117, 2019.

Y. Wang, G. Xu, A. Luo, L. Liang, and K. Jiang, “An online tacholess order tracking technique based on generalized demodulation for rolling bearing fault detection,” J. Sound Vib., vol. 367, pp. 233–249, 2016.

J. Wu, Y. Zi, J. Chen, and Z. Zhou, “A modified tacho-less order tracking method for the surveillance and diagnosis of machine under sharp speed variation,” Mech. Mach. Theory, vol. 128, no. 28, pp. 508–527, 2018.

M. L. Ruiz Barrios, F. E. Hernández Montero, J. C. Gómez Mancilla, and E. Palomino Marín, “Tacho-less automatic rotational speed estimation (TARSE) for a mechanical system with gear pair under non-stationary conditions,” Meas. J. Int. Meas. Confed., vol. 145, pp. 480–494, 2019.

J. Wu, Y. Zi, J. Chen, and Z. Zhou, “Fault diagnosis in speed variation conditions via improved tacholess order tracking technique,” Meas. J. Int. Meas. Confed., vol. 137, pp. 604–616, 2019.

Z. Cheng, M. Gao, X. Liang, and L. Liu, “Incipient fault detection for the planetary gearbox in rotorcraft based on a statistical metric of the analog tachometer signal,” Measurement, vol. 151, p. 107069, 2019.

D. Siegel, H. Al-Atat, V. Shauche, L. Liao, J. Snyder, and J. Lee, “Novel method for rolling element bearing health assessment - A tachometer-less synchronously averaged envelope feature extraction technique,” Mech. Syst. Signal Process., vol. 29, pp. 362–376, 2012.

V. Sharma and A. Parey, “Frequency domain averaging based experimental evaluation of gear fault without tachometer for fluctuating speed conditions,” Mech. Syst. Signal Process., vol. 85, pp. 278–295, 2017.

S. Schmidt, P. S. Heyns, and J. P. de Villiers, “A tacholess order tracking methodology based on a probabilistic approach to incorporate angular acceleration information into the maxima tracking process,” Mech. Syst. Signal Process., vol. 100, pp. 630–646, 2018.

P. Kuo Weng and J. S. Shie, “A revolving retro-reflective marker for an optical tachometer,” Sensors Actuators A. Phys., vol. 24, no. 3, pp. 203–207, 1990.

C. Kuo, M. Fanton, L. Wu, and D. Camarillo, “Spinal constraint modulates head instantaneous center of rotation and dictates head angular motion,” J. Biomech., vol. 76, pp. 220–228, 2018.

H. Chen, M. C. Schall, and N. Fethke, “Accuracy of angular displacements and velocities from inertial-based inclinometers,” Appl. Ergon., vol. 67, pp. 151–161, 2018.

Q. Hu, J. Zhang, and Y. Zhang, “Velocity-free attitude coordinated tracking control for spacecraft formation flying,” ISA Trans., vol. 73, pp. 54–65, 2018.

E. Allseits, V. Agrawal, J. Lučarević, R. Gailey, I. Gaunaurd, and C. Bennett, “A practical step length algorithm using lower limb angular velocities,” J. Biomech., vol. 66, pp. 137–144, 2018.

Z. Hou, Y. Geng, B. Wu, and S. Huang, “Spacecraft angular velocity trajectory planning for SGCMG singularity avoidance,” Acta Astronaut., vol. 151, no. May, pp. 284–295, 2018.

T. Ito et al., “Active use of solar radiation pressure for angular momentum control of the PROCYON micro-spacecraft,” Acta Astronaut., vol. 152, no. August 2017, pp. 299–309, 2018.

R. Losero, J. Lauber, and T. M. Guerra, “Virtual strain gauge based on a fuzzy discrete angular domain observer: Application to engine and clutch torque estimation issues,” Fuzzy Sets Syst., vol. 343, pp. 76–96, 2018.

Z. Yang, J. Huo, and X. Han, “Angular-rate sensing by mode splitting in a Whispering-gallery-mode optical microresonator,” Meas. J. Int. Meas. Confed., vol. 125, no. July 2017, pp. 78–83, 2018.

X. Liu, S. Wang, T. Zhang, R. Huang, and Q. Wang, “A zero-velocity detection method with transformation on generalized likelihood ratio statistical curve,” Meas. J. Int. Meas. Confed., vol. 127, no. March, pp. 463–471, 2018.

A. F. Chávez-Gonzalez, P. Martínez-Ortiz, J. A. Pérez-Benítez, J. H. Espina-Hernández, and F. Caleyo, “Comparison of angular dependence of magnetic Barkhausen noise of hysteresis and initial magnetization curve in API5L steel,” J. Magn. Magn. Mater., vol. 446, pp. 18–27, 2018.

M. Patel, “Spiking and Excitatory/Inhibitory Input Dynamics of Barrel Cells in Response to Whisker Deflections of Varying Velocity and Angular Direction,” Neuroscience, vol. 369, pp. 15–28, 2018.

H. Alrowais et al., “Bio-inspired fluidic thermal angular accelerometer with inherent linear acceleration rejection,” Sensors Actuators, A Phys., vol. 279, pp. 566–576, 2018.

C. C. Lin and F. L. Yang, “A new image processing algorithm for three-dimensional angular velocity measurement and its application in a granular avalanche,” Adv. Powder Technol., vol. 29, no. 3, pp. 506–517, 2018.

L. Iafolla, L. Witthauer, A. Zam, G. Rauter, and P. C. Cattin, “Proof of principle of a novel angular sensor concept for tracking systems,” Sensors Actuators, A Phys., vol. 280, pp. 390–398, 2018.

B. F. Mentiplay, M. Banky, R. A. Clark, M. B. Kahn, and G. Williams, “Lower limb angular velocity during walking at various speeds,” Gait Posture, vol. 65, no. March, pp. 190–196, 2018.

Q. ZHU, G. MA, X. WANG, and A. WU, “Attitude control without angular velocity measurement for flexible satellites,” Chinese J. Aeronaut., vol. 31, no. 6, pp. 1345–1351, 2018.

A. C. Y. Yuen et al., “Numerical study of the development and angular speed of a small-scale fire whirl,” J. Comput. Sci., vol. 27, pp. 21–34, 2018.

H. H. Lee, J. I. Yoon, and H. S. Kim, “Single-roll angular-rolling: A new continuous severe plastic deformation process for metal sheets,” Scr. Mater., vol. 146, pp. 204–207, 2018.

M. J. F. Digonnet and M. J. Grant, “Comments on ‘Simultaneous measurement of angular velocities of two vertical directions in a slow-light structure,’” Opt. Fiber Technol., vol. 45, no. December 2017, pp. 250–254, 2018.

H. Gui and G. Vukovich, “Distributed almost global finite-time attitude consensus of multiple spacecraft without velocity measurements,” Aerosp. Sci. Technol., vol. 75, pp. 284–296, 2018.




DOI: https://doi.org/10.18196/jrc.1315

Refbacks

  • There are currently no refbacks.


Copyright (c) 2020 Journal of Robotics and Control

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

 

Journal of Robotics and Control (JRC)

P-ISSN: 2715-5056 || E-ISSN: 2715-5072
Organized by Peneliti Teknologi Teknik Indonesia
Published by Universitas Muhammadiyah Yogyakarta in collaboration with Peneliti Teknologi Teknik Indonesia, Indonesia and the Department of Electrical Engineering
Website: http://journal.umy.ac.id/index.php/jrc
Email: jrcofumy@gmail.com

Kuliah Teknik Elektro Terbaik