Information System Prototyping of Strawberry Maturity Stages using Arduino Uno and TCS3200

Authors

  • Ariagi Juliano universitas ibn khaldun bogor
  • Ade Hendri Hendrawan Universitas Ibn Khaldun Bogor
  • Ritzkal Ritzkal Universitas Ibn Khaldun Bogor

DOI:

https://doi.org/10.18196/jrc.1319

Keywords:

Strawberry, TCS3200, WEB.

Abstract

Strawberry is one of the commodities of subtropical fruits growing in Indonesia. It has a high economic value, attractive appeal in a red and fresh sweet fruit. The color of a strawberry shows its maturity stages, and the strawberry maturity stages affect postharvest quality. The research aimed to design and implement a tool to approve and apply the maturity stages of strawberries using Arduino Uno and display the information on the web. The method included needs analysis and analysis of work, and the design consisted of hardware design and network design. The testing consisted of TCS3200 sensor testing, LCD testing, servo motor testing, and WEB testing. The results of this study found that when the strawberry fruit was declared mature by the TCS3200 sensor as the color detection sensor, the LCD would display the texts, and the servo would open. The system on the WEB would display the total information of the sorted strawberries.

References

A. B. Zia, M. A. Ali, M. O. Zeb, U. Shafiq, S. R. Fida, and N. Ahmed, “Development of microfluidic lab-on-disc based portable blood testing point-of-care diagnostic device,” in 2016 IEEE EMBS Conference on Biomedical Engineering and Sciences (IECBES), 2016, pp. 142–145.

S. Kabachok and D. Zhigulin, “Design of digital CCD spectrometer,” in 2016 IEEE 7th International Conference on Advanced Optoelectronics and Lasers (CAOL), 2016, pp. 48–50.

M. R. Sathuluri, S. K. Bathula, P. Yadavalli, and R. Kandula, “IMAGE processing based intelligent traffic controlling and monitoring system using Arduino,” in 2016 International Conference on Control, Instrumentation, Communication and Computational Technologies (ICCICCT), 2016, pp. 393–396.

A. C. Paglinawan et al., “Detection of three visual impairments: Strabismus, blind spots, and blurry vision in rural areas using Raspberry PI by implementing hirschberg, visual field, and visual acuity tests,” in 2017IEEE 9th International Conference on Humanoid, Nanotechnology, Information Technology, Communication and Control, Environment and Management (HNICEM), 2017, vol. 2018-Janua, pp. 1–9.

M. M. Kamal, A. I. Bayazid, M. S. Sadi, M. M. Islam, and N. Hasan, “Towards developing walking assistants for the visually impaired people,” in 2017 IEEE Region 10 Humanitarian Technology Conference (R10-HTC), 2017, vol. 2018-Janua, pp. 238–241.

M. F. Ahmad, H. J. Rong, S. S. N. Alhady, W. Rahiman, and W. A. F. W. Othman, “Colour tracking technique by using pixy CMUcam5 for wheelchair luggage follower,” in 2017 7th IEEE International Conference on Control System, Computing and Engineering (ICCSCE), 2017, vol. 2017-Novem, no. November, pp. 186–191.

M. F. Ibrahim, F. Zulkifli, M. R. H. M. Nizam, A. B. Huddin, and A. Hussain, “An RGB-D visual feedback controller for a differential drive attachable wheel system 1,” in 2017 6th International Conference on Electrical Engineering and Informatics (ICEEI), 2017, vol. 2017-Novem, pp. 1–7.

A. J. Rau, J. Sankar, A. R. Mohan, D. Das Krishna, and J. Mathew, “IoT based smart irrigation system and nutrient detection with disease analysis,” in 2017 IEEE Region 10 Symposium (TENSYMP), 2017, pp. 1–4.

G. S. Sathiya devi, “Blood leakage monitoring system in Hemodialysis therapy,” in 2016 International Conference on Communication and Electronics Systems (ICCES), 4992, pp. 1–5.

F. Ahmad, Tanveerulhaq, I. Ishaq, D. Ali, and M. F. Riaz, “Bionic Kinect device to assist visually impaired people by haptic and voice feedback,” in 2016 International Conference on Bio-engineering for Smart Technologies (BioSMART), 2016, pp. 1–4.

N. B. Bhagat and S. D. Markande, “Automatic grading of potatoes with fuzzy logic,” in 2016 Online International Conference on Green Engineering and Technologies (IC-GET), 2016, pp. 1–4.

M. Franzius, M. Dunn, N. Einecke, and R. Dirnberger, “Embedded Robust Visual Obstacle Detection on Autonomous Lawn Mowers,” in 2017 IEEE Conference on Computer Vision and Pattern Recognition Workshops (CVPRW), 2017, vol. 2017-July, pp. 361–369.

A. Tse, J. Saegnwipharat, K. Supayanant, and C. Pornpanomchai, “Controlling children-toy tank by using image processing technique,” in 2016 Fifth ICT International Student Project Conference (ICT-ISPC), 2016, pp. 73–76.

M. M. Garcillanosa, J. M. L. Pacheco, R. E. Reyes, and J. J. P. San Juan, “Smart Detection and Reporting of Potholes via Image-Processing using Raspberry-Pi Microcontroller,” in 2018 10th International Conference on Knowledge and Smart Technology (KST), 2018, pp. 191–195.

Y. Jia, G. Yang, and J. Saniie, “Real-time color-based sorting robotic arm system,” in 2017 IEEE International Conference on Electro Information Technology (EIT), 2017, pp. 354–358.

A. Murthy, S. S. Rao, M. A. Herbert, and Navin Karanth P, “Experimental study on linear displacement measurement sensor using RGB color variation technique with PID controller,” in 2017 International Conference on Computer, Communications and Electronics (Comptelix), 2017, pp. 241–247.

M. Wali-ur-Rahman, S. I. Ahmed, R. Ibne Hossain, T. Ahmed, and J. Uddin, “Robotic Arm with Proximity and Color Detection,” in 2018 IEEE 7th International Conference on Power and Energy (PECon), 2018, pp. 322–326.

G. Sonal, P. Raninga, and H. Patel, “Design and implementation of RGB color line following robot,” in 2017 International Conference on Computing Methodologies and Communication (ICCMC), 2017, vol. 2018-Janua, no. Iccmc, pp. 442–446.

K. Khade, R. Naik, and A. Patil, “Design of all color line follower sensor with auto calibration ability,” in 2017 7th International Symposium on Embedded Computing and System Design (ISED), 2017, vol. 2018-Janua, pp. 1–5.

G. I. E. Panie and A. B. Mutiara, “Development of Robotic Arm for Color Based Goods Sorter in Factory Using TCS3200 Sensor with a Web-Based Monitoring System,” in 2018 Third International Conference on Informatics and Computing (ICIC), 2018, pp. 1–6.

F. C. Ferreira, M. F. Santos, and V. B. Schettino, “Computational vision applied to mobile robotics with position control and trajectory planning: Study and application,” in 2018 19th International Carpathian Control Conference (ICCC), 2018, no. Section VII, pp. 253–258.

S. Saha, R. Hasan Rajib, and S. Kabir, “IoT Based Automated Fish Farm Aquaculture Monitoring System,” in 2018 International Conference on Innovations in Science, Engineering and Technology (ICISET), 2018, no. October, pp. 201–206.

J.-H. Li, Y.-S. Ho, and J.-J. Huang, “Line Tracking with Pixy Cameras on a Wheeled Robot Prototype,” in 2018 IEEE International Conference on Consumer Electronics-Taiwan (ICCE-TW), 2018, pp. 1–2.

A. I. Rusu, A. Florescu, and S. G. Rosu, “Efficient Navigation of a Robot Based on an Improved Contrast of Colours Algorithm,” in 2018 IEEE 24th International Symposium for Design and Technology in Electronic Packaging (SIITME), 2018, no. 33, pp. 37–42.

A. Singh, N. B. Balam, A. Kumar, and A. Kumar, “An Intelligent Color Sensing system for building wall,” in 2016 International Conference on Emerging Trends in Communication Technologies (ETCT), 2016, pp. 1–4.

H. Rashid, A. S. . R. Al-Mamun, M. S. R. Robin, M. Ahasan, and S. M. T. Reza, “Bilingual wearable assistive technology for visually impaired persons,” in 2016 International Conference on Medical Engineering, Health Informatics and Technology (MediTec), 2016, pp. 1–6.

Revantino et al., “Reconstruction of Color Mixing Model Using Tunable Light-Emitting Diode with Unequal Radiated Power,” in 2018 IEEE 3rd Optoelectronics Global Conference (OGC), 2018, pp. 56–59.

R. Alimuin, E. Calilung, and E. Dadios, “Implementation of machine vision as an input to a fuzzy water level control system,” in 2017IEEE 9th International Conference on Humanoid, Nanotechnology, Information Technology, Communication and Control, Environment and Management (HNICEM), 2017, vol. 2018-Janua, pp. 1–6.

M. R. Usikalu, B. M. Allen, W. A. Ayara, and I. O. Babarimisa, “Design of Autocrash Emergency Locator,” in 2018 IEEE Conference on Technologies for Sustainability (SusTech), 2018, pp. 1–4.

S. Mahat, S. H. Yusoff, S. A. Zaini, N. S. Midi, and S. Y. Mohamad, “Automatic Metal Waste Separator System In Malaysia,” in 2018 7th International Conference on Computer and Communication Engineering (ICCCE), 2018, pp. 366–371.

Ritzkal, "Manajemen Jaringan untuk Pemula," UIKA Press, 2018.

S. Syaiful, D. Hariyadi, "Case Study on Sustainable T-Junction Cibinong City Mall (CCM) in Bogor Indonesia, Asian Research Publishing Network (ARPN) Journal of Engineering and Applied Science, vol. 14, no. 17, 2019.

Downloads

Published

2020-02-26

How to Cite

[1]
A. Juliano, A. H. Hendrawan, and R. Ritzkal, “Information System Prototyping of Strawberry Maturity Stages using Arduino Uno and TCS3200”, J Robot Control (JRC), vol. 1, no. 3, pp. 86–91, Feb. 2020.

Issue

Vol. 1 No. 3 (2020): May

Section

Articles

License

Authors who publish with this journal agree to the following terms: 

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

 

This journal is based on the work at https://journal.umy.ac.id/index.php/jrc under license from Creative Commons Attribution-ShareAlike 4.0 International License. You are free to:

  1. Share – copy and redistribute the material in any medium or format.
  2. Adapt – remix, transform, and build upon the material for any purpose, even comercially.

The licensor cannot revoke these freedoms as long as you follow the license terms, which include the following:

  1. Attribution. You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
  2. ShareAlike. If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.
  3. No additional restrictions. You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.

 

• Creative Commons Attribution-ShareAlike (CC BY-SA)

Creative Commons License
JRC is licensed under an International License